查询词典 requirements

This paper, from the point of view of the whole system at first, analyzes the basic requirements in network environments. And it also gives a general architecture of this system. Whiling studying the control and monitor technologies of this system, different requirements and architectures are discussed respectively and at the same time the realization methods are also given.

本文首先从系统的全局体系结构出发，分析了网络环境下远程实验教学系统的基本功能要求，然后结合远程实时控制系统的实验教学的特殊要求，给出了通用意义上的基于网络的远程实时实验教学系统的体系结构框架。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Based on the above understanding, but also the overall economic and social development based on the Shanghai real estate market development and the basic requirements of the status quo, this year the real estate market will continue to focus on the mechanisms to accelerate the building of a more open, more integrated, better-regulated market, to establish WTO requirements, in line with the international standard management system and operational mechanism.

基于以上的认识，也基于上海经济社会发展的总体要求和房地产市场发展的基本现状，今年房地产工作的重点是继续加快市场机制建设，建立一个更加开放、更加统一、更加规范的房地产市场，建立符合WTO要求、与国际接轨的管理体制和运作机制。

Technology companies Is strong, engaged in the industry to employ more than 20 years of Senior Engineer 2, in instrumentation, medical equipment, petrochemicals, food machinery, aviation accessories, transport spare parts, construction hardware and military products, as well as highly machined parts and various Special requirements of the ball valve parts precision casting parts of the design, the stainless steel smelting and casting, may undertake all types of complex parts of different material requirements of the casting design, product weight from five grams to 20 kilograms can be manufactured.

公司技术力量雄厚，聘请从事本行业20余年的高级工程师2人，从事仪器仪表、医疗器械、石油化工、食品机械、航空配件、车船零配件、建筑五金和军工产品以及高难度机加工件和各种特殊要求的球阀的零部件精密铸造零件的工艺设计、不锈钢和碳钢的冶炼浇注，可承接各类复杂零件的不同材质要求的铸造设计，产品重量从5克到20千克均可制造。

Ship products within 65 meters scattered cargo ship, round container, oil tankers, Yulun, tugs, barges and other vessels of various sizes of steel and can be built based on customer specific requirements of different tonnage requirements of the coal bucket, steel structures, such as ship-Gallery.

船舶产品有65米以内散货轮、集装箱轮、油轮、渔轮、拖轮、趸船等各种大小钢质船舶，并能依据客户特定要求建造不同吨位要求的煤斗、钢结构通廊等船舶。

2 These requirements do not cover household electric ranges, electrode type appliances, skillets and frying type appliances, fondues, woks, tempuras, corn poppers, coffee makers and brewing type appliances, commercial cooking appliances, microwave cooking appliances, or appliances that are covered in individual requirements that are separate from this standard.

该要求不包括家用电器范围，电极类电器，煮锅和炸锅类电器，干酪机，中华锅，天麸罗机，爆玉米花机及咖啡机，酿造类的电器，商用蒸煮器具，微波炉或有个别要求而背离该标准的电器制品。

The Doppler frequency shift and the Doppler broadening are comprehensively utilized, the narrow-band phase plate is inserted between a collimating mirror and a focusing lens of an imaging probe, thereby implementing the spatial encoding of the Doppler information, realizing the imaging requirements on the spatial high-resolution three-dimensional speed vector, combining with the Doppler OCT method which is based on the phase resolution technology to meet the high-speed and high-sensitivity measurement requirements and finally realizing the speed vector imaging with high-resolution, high-speed, high-sensitivity and large-imaging range of the three-dimensional flow field of the microfluidic chip.

综合利用多普勒频移和多普勒展宽，并在成像探头的准直镜和聚焦透镜之间插入窄带相位片，实施多普勒信息的空间编码，实现空间高分辨三维速度矢量的成像要求，再结合基于相位分辨技术的多普勒OCT方法则能够满足高速度高灵敏度的测量要求，最终实现对微流控芯片立体流场的高分辨率、高速度、高灵敏度、大成像范围的速度矢量成像。

Any requirements of the Owner, which are in excess of the requirements of the rules and regulations as specified under "Rules, Regulations and Certificates" and/or the content of this Specification shall be subject to adjustment to the contract price, dead-weight, etc.

对于船东的任何要求，如果超过规范或规则中的要求或规格书中的规定，那么应考虑其对合同价以及载重的影响而进行调整。

The API classifications form the minimum requirements for many engine maker s who often impose additional performance requirements and run their own approval systems.

API分类标准为众多发动机生产商制定了最低要求，这些生产商通常也会根据自己的需要给出额外的性能要求，并采用自己的批准程序。

Responsible f controlling signatures, taking policy into account, urgency and effecting timeous fwarding of documents - Actioning all SVP travel requirements including drawing the itinerary and travel requirements of BMW Group visits - Representing the SVP and upholding the image of the BMW brand when interfacing with irate customers - Determining when the Direct should become involved and managing the process to a successful conclusion - Interfacing with dealers who need to communicate with the SVP on various issues - Handling external enquiries related to various Sales and Marketing issues.

它标志着华晨宝马沈阳工厂作为中国重要的高档车生产基地的雄厚实力，为宝马在中国的长期发展奠定了坚实的基础。目前，沈阳工厂拥有员工约3400人。 2006年1月，华晨宝马汽车有限公司被评为辽宁省十大纳税外资企业之一。 2006年3月，华晨宝马赞助了全国持续时间最长，影响力最大的全国副省级城市机关报短新闻竞赛，支持中国新闻事业的发展。 2006年4月，华晨宝马向沈阳市政府提供20辆BMW 523i作为\&2006中国沈阳世界园艺博览会\&开幕期间贵宾用车，并投资兴建\&德国园\&。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。