查询词典 requirements

The difference between requirements and default-build is that requirements cannot be overridden in any way.

要求和缺省构建之间的区别在于，要求是不能被覆写的。

By identifying clear requirements, the cost overruns and schedule slippage can be avoided due to the requirements ambiguity.

通过提出明确的要求，可避免因要求含糊而造成的费用超支和时间表的延误。

The law preempts any state or local requirements for reporting adverse events that are not identical to the federal requirements.

法律preempts任何国家或地方的要求报告不良事件并不相同联邦的要求。

Your firm has released products purporting to meet USP requirements when, in certain cases, they fail to meet such requirements.

… -你公司放行了声称符合 USP 要求的产品，但某些情况下，它们未能符合相关的要求。

HeGuoJiang quarterbacked the meeting in that President hu jintao when the important speech, from the party and national undertaking the overall development and strategic height, the comprehensive analysis of the current situation, the anti-corruption explicitly put forward further party building.the struggle against corruption and the overall requirements and main tasks in the new period, and the strengthening self-cultivation, leading cadres foster and promote good style of the importance and urgency and basic requirements and emphases, party building.the for further development and corruption, comprehensively promote the construction of a new great project of significant and profound meaning.

贺国强在主持会议时指出，胡锦涛总书记的重要讲话，从党和国家事业发展全局和战略的高度，全面分析了当前的反腐倡廉形势，明确提出了深入推进党风廉政建设和反腐败斗争的总体要求和主要任务，深刻阐述了新时期加强领导干部党性修养、树立和弘扬良好作风的重要性和紧迫性以及基本要求和工作重点，对于深入开展党风廉政建设和反腐败斗争，全面推进党的建设新的伟大工程，具有重大而深远的意义。

Fully stocked warehouse, material specifications can be fully meet the customer's normal requirements, if there are special specifications can be based on customer requirements and redissolving rolling forging.

公司仓库备货齐全，材质规格能够完全满足客户的正常需求，如有特殊规格，可根据客户要求进行重溶锻轧。

In respects of whether it is permitted, age of the sterilized, substantial requirements and procedural requirements.

立法在准许实施强制性绝育者的年龄、实体法上的理由、程序等方面有很大的不同。

A results of internal audits and evaluations of compliance with regulatory requirements and with other requirements to which the supplier subscribes

对供应商是否遵守法规要求和供应商同意之其他要求而进行的内部审核和合规性评价的结果

This paper, from the point of view of the whole system at first, analyzes the basic requirements in network environments. And it also gives a general architecture of this system. Whiling studying the control and monitor technologies of this system, different requirements and architectures are discussed respectively and at the same time the realization methods are also given.

本文首先从系统的全局体系结构出发，分析了网络环境下远程实验教学系统的基本功能要求，然后结合远程实时控制系统的实验教学的特殊要求，给出了通用意义上的基于网络的远程实时实验教学系统的体系结构框架。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

But this is impossible, as long as it is engaging in a market economy, there are risks in any operation.

但是，这是不可能的，只要是搞市场经济，是有风险的任何行动。

We're on the same wavelength.

我们是同道中人。