查询词典 rectangular axes

The key technology of this method is to quickly converge the sensitive axes of the mechanical gyroscope to the intersection line of the meridional plane and the horizontal plane based on the principle of gyroscope compass, to isolate payload from platform disturbance with the gyroscope and two degrees of freedom gimbals, to obtain the attitude angle of the platform by electro-optical sensor on the gimbals, and to make the sight slaved to the sensitive axes of the gyroscope to realize the indirect stabilization.

利用陀螺罗经原理，使机械陀螺的敏感轴快速收敛于子午面和水平面的交线上，并借助陀螺定轴性和2自由度环架，使陀螺隔离运动载体的扰动；通过环架上的光电传感器测出运动载体的姿态角，使观瞄镜的瞄准线随动于陀螺的敏感轴，实现间接稳定。

The disposal of magnetic pole In order to decrease magnetic hysteresis loss ,Magnetic poles are put along the axes of rotor and magnetic flux parallel the axes of rotor.

2处置磁极为了减少磁磁滞损耗，磁极是把沿轴线和转子磁通平行轴线的转子。

Two-dimensional scatter plot of principal axes analysis,systematic cluster tree and the minimal spanning tree on the basis of niche overlaps were drawn,which revealed the ecological similarity of 42 moss species.The combinative application of principal axes analysis,systematic cluster analysis and minimal spanning tree method on the basis of niche overlaps could express the ecological similarities among species intuitively.

以此为指标，分别应用主坐标排序、图论聚类及系统聚类分析方法，作出了反映42种地面藓类的种间生态关系的二维投影图、最小生成树和动态聚类图。3种方法相结合，能够对生态位重叠值矩阵进行直观地表达，并使所表达的藓类种间关系具有确切的生态学含义。

Planar motion also requires that axes of all prismatic pairs and all revolute axes be normal to the plane motion.

平面运动需要所有的棱形副的轴和转动副的轴都垂直于运动平面。

No.3: When the valve fully open, the angle between sphere body hole-through axes and valve body hole-throught axes Max.

阀门全开时，球体通孔轴线与阀体通孔轴线的夹角不大于3

This milling machine has fixed cross-rail and column structure. The national patent technology "the new multiple guideway" and CNC universal milling head with AC axes(3axes +2axes) type are applied to it. It can realizes rotate index ±370o at AC axes. Equipped with domestic or imported CNC system and capability, the machine can realize pentahedron machining.

产品采用定梁定柱结构，刚性强；应用《新型复合导轨》国家专利技术和AC轴（3轴+2轴）型数控自动万能铣头核心技术，可实现AC轴±370o自动旋转分度；选配国产和进口数控系统，自动完成多种空间方向的加工，实现五面体加工功能。

The transform matrixes were obtained to converting coordinates between incident plane axes and crystal eigent axes.

刚体中心惯量主轴上任意一点的惯量主轴与刚体的三条中心惯量主轴重合或平行。

Two series of drained tests with fixed principal stress axes and cyclic rotation of principal stress axes were conducted with a hollow cylinder apparatus at Hong Kong University of Science and Technology.

采用香港科技大学的空心圆柱扭剪仪进行了应力主轴固定单调剪切和应力主轴循环旋转两种不同路径的排水试验。

For the tests under the condition of cyclic rotation of principal stress axes, the magnitudes of three effective principal stresses were kept constant and only the principal stress axes rotated cyclically from 0 to 180 relative to vertical axis.

在应力主轴循环旋转试验中，控制施加在试样上的3个有效主应力的大小不变，仅应力主轴在0°~180°循环旋转。

A new cyclic constitutive model for sands which can describe the deformation behavior of sands under combined variation of principal stress axes and magnitudes was developed based on the above physical fundamentals. And its effectiveness under the complex stress paths including cyclic rotation of principal stress axes is verified by a good comparison of model simulation with test results for sands.

2基于对应力主轴循环旋转条件下砂土的基本变形规律的认识，吸收和借鉴已有弹塑性本构模型研究成果中的合理概念和建模方法，建立了一个可合理描述应力主轴循环旋转效应及主应力幅值大小与应力主轴方向循环耦变效应的砂土弹塑性本构模型，并对该模型在包含应力主轴旋转的复杂循环应力路径下的有效性进行了验证。

A small, rubber-headed hammer used in examination or diagnosis by percussion.

叩诊槌用在通过''。'振荡'。''所作的检查或诊断中的橡皮头的''。'小'。''槌

Affixes are limited in number in a language, and are generally classified into three subtypes, namely, prefix, suffix, and infix, depending on their position with reference to the root or stem of the word.

语言中词缀的数量总是有限的，根据它们跟词根或词干的相对位置，一般可以把词缀分外三小类：前缀，后缀和中缀。