查询词典 real error

The experiment results show that the measuring errors are more than 10' and these are zero point error and the non-lincar system error when the two obliquity angles of the kingpin are more than 15°, and the system errors increase as the kingpin obliquities increase.

试验表明：受检四轮定位仪当主销两倾角均大于15时，其测量误差大于10'，存在零点和线性度系统误差，且系统误差随主销倾角的增大而增大，从而解决了测量主销倾角量值检定的问题。

The error of the elongation is 2.3%, by the multi-dimension linear regression model, the relative error are from ? 5% to ? 15% respectively. Comparing the results, it can be found that the neural network overmatches the multi-dimension linear regression. So that, the model can be used in the production of the marine propeller aluminum bronze.

计算结果表明，三项输出的预测值与实测数据接近，抗拉强度和屈服强度的相对误差在±1％的范围以内，延伸率的最大绝对误差为2.3％，明显优于多元线性回归模型±5％—±15％的误差，能较好地满足工程应用的要求，对高强度船用螺旋桨铝青铜的生产具有一定的指导意义。

Also, the error rate of a teleportation channel has no concern with the signal being transmitted. This is because the non-trivial error patterns are permuted under teleportation.

此外，研究中还发现，在隐形传输下，因为改变了非平凡误差的模型序列，所以隐形传输信道的误差率与正被传输的信号无关。

It is the nature of every man to error, but only the fool perseveres in the error.

也不知道你们那边的时差和我们差多少，要注意休息！

Traditional error models can not give precised error prediction or lack of universality in use.

本文对目前DEM精度研究现状进行了较为系统的回顾和剖析，指出了传统的DEM全局精度指标和。。。

Second,effect of several error factors,such as tool presetting error,non-parallelism er...

通过上述分析，确定试验台两轴不平行是影响工件面形精度的主要误差因素。

Ting and fusing Global texture relighting and fusing includes global relighting of multiple textures based on least mean-square error, global color correction of multiple textures based on least mean-square error, and weighted fusing of multiple overlapped textures.

3全局纹理重光照与细节融合技术研究基于最小均方差的多幅纹理全局亮度校正和色度校正技术、多幅重叠纹理加权融合技术。

The error evaluation method most frequently used in current applications is the quadric error metrics, originally proposed by Garland and Heckbert in [9], in which a quadric (represented by a symmetric, positive semi-definite matrix) is associated with each vertex, subsuming the sum of the squared distances of the vertex to all its incident planes.

当前采用的最广泛的误差评估方法是QEM方法。这个方法中，每一个顶点都与一个二次误差相关联，包含了顶点到其相邻面距离的平方和。

Uncertain upper boundary function is learned on-line by using FNN, and proportion controller strengthens the completeness of FNN control strategy. FNN is trained by using disparity target learning error produced by FIE. This can avoid supersaturating problem made by feedback error directly, and restrain influence of measuring noise and improve control performance.

由于模糊技术与神经网络的结合能弥补彼此的不足，因此本文提出了一种模糊神经网络控制器与比例控制器相结合的控制方案，采用模糊神经网络在线学习不确定函数的上界，比例控制器增强模糊神经网络控制策略的完备性。

Calculation formulae were derived for the maximum angle error of the outputting gear caused by the tangential synthetic tolerance and the last motion error angle caused by normal directional side clearance.

推导出了由切向综合公差引起的输出齿轮最大角度误差的计算公式和由法向侧隙引起的空回误差角的计算公式。

I think people in this lifetime in a rebirth.

我觉得人在这一生里其实也在轮回。

He had to tie her hands together.

他不得不把她的双手绑在一起。