查询词典 reaction rate

The phase equilibrium data of SBO-FAME-Methanol, SBO-FAEE-Ethanol and Glycerol-FAEE-Ethanol systems were measured. The results indicated that it involved two different stages: liquid-liquid-solid reaction stage and liquid-solid reaction stage. When the molar ratio of methanol to oil is 12:1 at 65℃, the turning point is at a 55% biodiesel yield. The liquid-liquid-solid reaction model was proposed based on the double-membranes theory. It indicated that the process is reaction and mass transfer controlled together at the first stage, and the second stage is reaction controlled. The predictions of the model are matched with the experimental results.In the end, the acid was extracted using methanol and ethanol from jatropha curcas l oil.

测定了生物柴油制备过程中的SBO-FAME-Methanol、SBO-FAEE-Ethanol、Glycerol-FAEE-Ethanol三组分相平衡数据，表明固体碱催化过程分为液-液-固和液-固两个反应阶段，在醇油摩尔比为12：1、65℃的初始反应条件下，转化率达到55%时，为第一阶段向第二阶段的转折点；基于双膜理论建立了固体碱催化制备生物柴油的非均相液-液-固反应模型，表明两个反应阶段分别为传质、反应共同控制和反应控制，模型计算值与实验值吻合较好。

The copper-catalyzed 1,3-dipolar cycloaddition of alkynes with azides is a typical example of "click" reaction.1 Since the reaction enjoys the advantages of high efficiency and regioselectivity and requires mild reaction conditions and simple purification procedures, it has become a versatile synthetic tool with applicability in diverse areas including bioconjugation and surface modification.2 The click reaction has also been utilized in polymer science with emphasis on the functionalization of preformed polymers through postpolymerization approaches.3 The effort of developing the reaction into a new polymerization technique, however, has met with only limited success.

登录后回答可以获得经验值奖励，并可以查看和管理所有的回答。登录|铜催化1，3偶极环加成反应的炔烃与叠氮化物是&点击&自reaction.1典型的例子反应享有高效率的优势和区域选择性并要求反应条件温和，简单净化程序，它已成为一个多功能综合工具在包括生物耦合和不同领域的适用性表面modification.2的点击反应亦是利用聚合物科学与功能化的重点通过postpolymerization approaches.3预制聚合物发展到一个新的聚合反应的努力技术，然而，只取得有限的成功。

The progress levels of symptoms after pathogen infection showed that interaction of gray leaf spot pathogen and host has differentiation or polymorphism. The progress levels of symptoms is different.The aggressively has polymorphism. The pathogenicity of different isolates in same cultivar has polymorphism, or the host reaction type of same isolate in different cultivars has polymorphism.The host reaction type has differentiation. There are seven types of host reaction in cultivar and inbred after infected by GLS pathogen:Rectangular lesion without chlorotic halo, Rectangular lesion with chlorotic halo,Irregular lesion without chlorotic halo,Irregular lesion with chlorotic halo, Spot lesion with chlorotic halo,Rectangular and irregular lesionand Rectangular and spot lesion. The host reaction type is coalesced lesion when disease severely. Frequency of each reaction types is different.

通过对玉米灰斑病菌侵染后的显症过程的系统观察，可在组织水平上说明该病菌与寄主互作反应存在分化或多样性：玉米灰斑病菌不同菌株侵染后显症过程表现出明显的差异；玉米灰斑病菌在侵袭力上存在多样性，菌株间对同一种品种的致病性表现多样化，或者同一菌株对不同品种侵染引起的寄主反应表现为多样性；病斑反应型的分化，玉米灰斑病菌侵染玉米品种或自交系后，主要有7种病斑反应类型，即RH型、RN型、IRH型(不规则形具褪绿晕圈病斑)、IRN型(不规则形无褪绿晕圈病斑)、SH型、RI型(长矩形与不规则形混合病斑)和RS型(长矩形与斑点形混合病斑)，若发病严重，病斑连成片，而且这些反应类型出现的频率也不同。

Effects of microwave power, reaction time, reaction temperature, solvent etc. on reaction were studied by a single factor tests. The results show that maleic acid is more active than fumaric acid; the introduction of methyl group on the double bond can weak the reactivity of the Michael addition reaction; the ester base is more propitious to complete the Michael addition reaction than the nitrile base.

为研究微波下迈克尔反应的规律，本文采用单模聚焦微波有机合成仪，通过对顺丁烯二酸、反丁烯二酸和氨水合成DL-天冬氨酸、顺式3-甲基丁烯二酸和氨水合成3-甲基天冬氨酸、丙烯酸甲酯和氨水合成β-丙氨酸、丙烯腈和氨水合成β-氨基丙腈等五个反应对迈克尔加成反应进行了研究。

Melting point 3410 ℃, boiling point 560 ℃, relative density of 1935, F the external electronic structure of 5d46s2, in the chemical reaction time is very easy to lose 1-6 electronic, but also can get 1-2 electronic, so oxidation number of 0,± 1,± 2, 3, 4 , 5 and 6, with 6 price of the most stable compounds, such as WO3 does not dissolve in water, the air will form in the tungsten trioxide thin protective layer of tungsten, tungsten with fluorine at room temperature, chemical combination, red hot when there is no moisture and Bromine iodide together, red hot when you can and water reaction WO3, at room temperature reaction of tungsten with aqua regia, but the hot concentrated hydrochloric acid and sulfuric acid can only be played with its weak response, but molten nitrate, nitrite, too Hydrogen peroxide, sulfur steam, steam and other phosphorus can play intense reaction, high temperature can not be carbon, boron and silicon reaction of binary compounds, widely used in industrial tungsten steel and tungsten carbide, pure tungsten filament is used to the system, and X-ray tube Tube heating components, semiconductor components can be prepared tungsten silicide, tungsten industrial production is white or black tungsten ore tungsten ore refining.

熔点3410℃，沸点560℃，相对密度1935，F外围电子结构为5d46s2，在化学反应时很容易丢掉1—6个电子，也能得到1—2个电子，所以氧化数为0、±1、±2、＋3、＋4、＋5和＋6，以＋6价化合物最稳定，如WO3不溶于水，空气中的钨会形成薄层三氧化钨保护层，钨能与氟在室温下化合，红热并无潮气时能与溴、碘化合，红热时还能和水反应生成WO3，室温下钨可与王水反应，但热的浓盐酸和硫酸只能与其起微弱反应，但对熔融的硝酸盐、亚硝酸盐、过氧化氢、硫蒸汽、磷蒸汽等能起激烈反应，高温下不能与碳、硼和硅反应生成二元化合物，工业上广泛使用钨钢和碳化钨，纯钨用来制灯丝、电子管和X射线管的发热元件，硅化钨可制半导体元件，钨工业生产是将白钨矿石或黑钨矿石精炼。

The effects of different factors on the laser-induced graft polymerization on the PET surface were analyzed, and the mechanisms were discussed. The factors were: 1 Monomers with smaller molecules resulted in better modification than polymeric monomers. Acrylamide monomer was chosen as hydrophilic modifier finally; 2 Higher concentration of the monomer solution favored the graft reaction; 3 With the increasing laser fluence, the surface hydrophilicity of PET films increased at first, then decreased. More laser pulses led to a more hydrophilic surface; 4 Benzophenone as a photosensitizer hindered the graft polymerization; 5 The homopolymer retardant of ammonium iron sulfate hexahydrate in a proper concentration retarded the formation of homopolymers and promotes the graft copolymerization; 6 The solvent of monomer solution also affected the graft reaction. Different solvents functioned in different ways. Ethanol can promote the graft reaction because of the activity of hydrogen in its structure; 7 pH value of the monomer solution affects the polymerization rate, and a lower pH value was favorable to the graft reaction.

这些影响因素的作用分别为：1小分子单体的表面改性效果好，确定以丙烯酰胺为亲水性改性单体；2较高的单体溶液浓度有利于接枝反应；3激光能量密度增大，薄膜表面亲水性先显著增强，后又减弱；激光脉冲次数越多，改性后表面亲水性越强；4光敏剂BP对PET表面接枝聚合反应有阻碍作用；5适当浓度的均聚物抑制剂六水合硫酸铁铵能减少单体均聚物的生成，促进接枝聚合；6单体溶液的溶剂也影响接枝聚合的反应进程，不同溶剂的影响作用原理不同，含较活泼氢的乙醇能促进接枝反应；7溶液pH值影响单体聚合速率，pH值较低有利于接枝反应。

This complex reaction was phenolic electronic substitution reaction, so reaction rate was related with the positive electricity of pro-electronic reagent, as well as the form of aromatic hydrocarbons. Rates of chlorination of phenol and 2-monochlorophenol were faster in alkaline water than that in weak acid water, so 2,4-dichlorophenol and 2,4,6-trichlorophenol formation concentrations increased with the reaction time.

该复合反应属于酚类电子取代反应，反应速率与亲电子试剂的阳电性以及芳香烃的形式有关，碱性水环境中氯取代苯酚和2-一氯酚的速率要快于在弱酸性水环境；随着pH的升高，2，4-DCP和2，4，6-TCP的生成浓度也不断增加。

We studied the effect of water on the palladium acetate-catalyzed coupling reaction of aryl boronic acid with aryl bromide or acyl chloride in ionic liquid or PEG, and found that water had a remarkable rate accelerating effect on the Suzuki reaction and Suzuki-Type reaction when other reaction conditions were uniform.

研究了水对离子液体或聚乙二醇中Pd2催化的卤代苯或苯甲酰氯与苯硼酸的Suzuki和Suzuki-Type偶联反应收率的影响。

The results show that this reaction proceeds in two step: 1 silylene and formaldehyde form an intermediate complex, which is a kind of exothermal reaction with no barrier; 2 the intermediate complex isomerizes to sive the product. The barrier for the second step is 51.4kJ·mol^-^1 at MP2/6-31G^*//6-31G^* level (with zero-point energies correction). In view of dynamics and thermodynamics, it is between 300～400K that the reaction will have not only larger spontaneous tendency and equilibrium constant but also quicker reaction rate.

结果表明，此反应历程由两步组成：1硅烯与甲醛生成一中间配合物，是一无势垒的放热反应，2中间配合物异构化为产物，此步势垒经零点能校正后只有51.4kJ·mol^-^1(MP2/6-31G^*//6-31G^*)；从热力学和动力学的综合角度考虑，该反应在300～400K温度下进行为宜，如此，反应既有较大的自发趋势和平衡常数，又具有较快的反应速率。

The results show that the optimal parameters of esterification are as follows: 4% of SO42-/ZrO2, molar ratio of methanol to litsea cubeba kernel oil 101, 68 ℃ of reaction temperature and 4 h of reaction time, the acid value decreases to 2.52 mg/g. Compared with the traditional acidic-catalyzed method, this method has the advantages of no acid proof equipment, easy to recycle catalyst and no acidic waste water emission. The optimal parameters of transesterification are as follows: 25 ℃ of reaction temperature, 0.5% of hexadecyl-trimethyl-ammonium bromide, 1% of NaOH, molar ratio of methanol to the oil 61 and 15 min of reaction time. The ester exchanging rate is 97.6%. This method adopts phase transfer catalyst and produces industry prospect, which has many advantages such as energy-saving and time-saving under room temperature.

研究结果表明，固体酸SO42-/ZrO2催化酯化反应的最佳条件为：油重4%的SO42-/ZrO2，醇油摩尔比为101，温度为68 ℃，反应时间为4 h，原油酸值降到2.52 mg/g；该法相对浓硫酸催化酯化法具有不需耐酸设备、催化剂易回收、无废水排放等优点；相转移催化酯交换反应的最佳条件为：温度为 25 ℃，0.5%的十六烷基三甲基溴化铵，油重1%的NaOH，醇油摩尔比为61，反应15 min，原油酯交换率达到97.6%；采用相转移催化技术，反应在常温下进行，大大减少了能耗，缩短了反应时间，具有的产业化前景。

"Yes, now you can give yourself airs," she said, you have got what you wanted.

"对了，您现在高兴了，"她说道，这是您所期待的。

Then the LORD said to me: Rebel Israel is inwardly more just than traitorous Judah.

上主于是对我说：＂失节的以色列比失信的犹大，更显得正义。