查询词典 ratchet gear

Gear wear and tear maintenance: Gear tooth wear is mainly the meshing parts, involute gear face and ends flat.

齿轮的磨损维修：齿轮的磨损部位主要是齿的啮合、渐开线工作面和齿轮两端平面。

This article first determines major component's structure pattern and the main design variable; Then the reference similar driving axle's structure, determines the overall project design; Finally to the host, the driven bevel gear, the differential device circular cone planet gear, the rear axle shaft gear, the full floating axle and the integral-type bridge shell's intensity carried on the examination as well as has carried on the life examination to the supporting bearing.

本文首先确定主要部件的结构型式和主要设计参数；然后参考类似驱动桥的结构，确定出总体设计方案；最后对主，从动锥齿轮，差速器圆锥行星齿轮，半轴齿轮，全浮式半轴和整体式桥壳的强度进行校核以及对支承轴承进行了寿命校核。

American Huixin straight teeth casting ladle, brake inside the gear box, hard make and difficult to maintain; it's nut gear of the hand wheel, with three radial direction space accumulate, difficult to ensure accuracy; while circular motion, it's shaft direction moving, gear have friction slidding, easy agglutination.

美国回信的直齿浇包，制动器在齿轮箱里面，难制作难维修；他的手轮轴上的螺母齿轮，有三处径向间隙累加，难保证精度；在园周运动的同时，有轴向移动，齿轮有摩擦滑动，易胶合。

Friction rubber draft gear, as one of high-capacity draft gears, is developed after friction steel spring draft gear. Rubber has energy absorption capability and non-linear rigidity capability, so the friction rubber draft gear's capacity is usually higher than the friction steel spring bumper.

摩擦式橡胶缓冲器是继摩擦式钢簧缓冲器之后开发的一种大容量缓冲器，这种缓冲器利用了橡胶自身具有吸收能量及非线性刚度的特性，因此其容量一般比摩擦式钢弹簧缓冲器高。

This article introduced the numerical control gear cutter's basic structure, the principle of work, gear cutter various movements' realization and controls, gear cutter related part's computation and monolithic integrated circuit control procedure diagram, electric control principle.

本文介绍了数控铣齿机的基本结构，工作原理，铣齿机各运动的实现及其控制，铣齿机有关部件的计算及单片机控制程序框图，电气控制原理。

The author researched into a new optimized design of gear-driven in quick-change gear box ,describing a way in detail to solve gear-driven parameter optimization by using optimization toolbox of Matlab.

研究了基于Matlab平台建立车床进给箱换向机构齿轮传动的优化设计模型，描述了利用Matlab优化工具箱解决进给箱齿轮传动参数优化问题的具体方法。

Reducing gear drives cam rotate to top half-turn and link gear of upper gate move, top disc opens and discharges. Spring device makes disc close and replace with displacement of cam. When cam rotates to bottom half-turn link, gear of sub-layer gate moves, below disc opens and discharges. The disc closes little by little with the displacement of cam. These two actions maintain a closed state of either disc on the pipe. So it can discharges and lock air at the same time.?

减速装置带动凸轮旋转至上半圈时，上层阀门的连杆机构互动，阀板逐渐打开卸灰，随着凸轮的旋转，弹簧机构使阀板逐渐关闭复位；凸轮旋转至下半圈时，下层阀门的连杆机构互动，阀板逐渐打开卸灰，随着凸轮的旋转又使阀板逐渐关闭，这样两个动作使管道上阀板始终有一个是关闭状态，因而，可使卸灰与锁气同时达到目的。

Shenzhen with Fu, Main: electroplating equipment, electroplating equipment supply all kinds of fittings fittings: Cross handle frames, plastic 65 tooth gear, 21 tooth plastic gear, plastic dual-V-Block, hexagonal screws 3 hours, 4 minutes plum screws, roller big axis, kegs of portable batteries, portable pail handle, hand-held drum gear hexagonal plastic punching: advantages: plastic punch hexagonal cylinder shape, the use of electrical conductivity, and fast access to medicine.

双V型胶座。深圳同富华，主营：电镀设备的各种配件供应电镀设备配件：十字柄架，65齿胶齿轮，21齿胶齿轮，双V型胶座，六角螺丝3分，梅花螺丝4分，滚筒大轴心，手提式小桶芯，手提小桶柄，手提齿轮六角滚筒胶板冲孔：优点：胶板冲孔六角滚筒成型后，使用时导电好，药水出入快。

The gear double-faced joggle instrument is the special system to measure the errors of the radial resultant error for one gear and the radial resultant error for one tooth of a gear.

齿轮双面啮合检查仪是检测齿轮径向综合误差ΔF"和齿轮一齿径向综合误差Δf"i的传统仪器。

The wind turbines can change the wind power to mechanical energy using the impeller and transmit the mechanical energy to a gear accelerating device, after joggle of one big gear and one or multiple small gears, each small gear can drive a generator to generate by a flexible projecting shaft set coaxially with small gears and provided support for small gears.

所述风力发电机组可利用叶轮将风能转化为机械能，并将机械能传递给齿轮增速装置，经过一个大齿轮与一个或多个小齿轮啮合后，每个小齿轮可通过为其提供支撑并与其同轴布置的柔性悬臂轴带动一个发电机发电。

" I' d like to get some rough idea about music in the baroque ear, please."

请简要介绍一下巴罗克时期的音乐，好吗？

The results showed that the peak latency and pattern of SEPs elicited by electrical needling in LI-l1 and MP were similar. The amplitude of SEPs elicited by electrical needling in LI-l1 was higher than that of MP. There was no obvious SEPs generation when MM was electrical needling.

结果显示，电针刺激曲池穴和其邻近桡侧伸腕长肌运动点诱发性脑电波的波形和波峰时间是类似的，只是穴位的诱发性脑电波波幅较大，而电针刺激非穴位点并没有明显的诱发性脑电位。