查询词典 radius

For the axicons with 20 mm radius, 10-2 cone angle, when using incident spherical wave whose radius of curvature varius from 1200 mm to 1400 mm, the focal length increases from 200 mm to 120 mm and the lateral intensity distribution increases only 15μm.

对于半径20 mm，锥角θ=1×10－2的圆锥透镜，采用曲率半径为1200~1400 mm的球面入射波，可扩展焦深200 mm到120 mm，光强的均匀性有明显改善，横向场能量分布形状改变量不超过15 μm，完全达到应用要求。

Experimental TEA CO2 laser with printed circuit board preionization is used. The laser has gain length of 90 cm. The resonator is composed of a total-reflective concave spherical mirror of curvature radius 20 m and a total-reflective plane mirror of mirror radius 4.5 mm, separated by 5 m distance.

实验中TEA CO2激光器采用印刷电路板预电离结构，增益长度90 cm，腔长5 m，球面全反射镜曲率半径20 m，输出端平面镜半径4.5 mm，得到了内环半径为4.5 mm、外环半径为5.5 mm的基模环形光斑输出。

It is proved that the obtained radial and tangential stress curve link glossily at hardening zone radius r=R, and softening zone radius r=R and curve of tangential stress σ(subscript θ)/p0-r/α has not up-pinnacled stress concentration especially, the result goes all the way with the experiment result of Japanese scholar Jiuwubosheng.

证明了所求得的巷道围岩径向和切向应力曲线在硬化区半径r=R和软化区半径r=R处均光滑连接，特别是所求得的切向应力σ/p0-r/α曲线没有尖峰向上的应力集中，此结果与日本学者久武胜保的试验结果一致。

METHODS: The endodontic instrument was assumed as a metal conical bar. The normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics. The relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, and metal elastic modulus were analyzed. The criteria for yielding and fracture of the instrument were discussed.

将根管器械刃部假设截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

METHODS: The endodontic instrument was assumed as a metal conical bar, the normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics , the relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, metal elastic modulus were analyzed, the criteria for yielding and fracture of the instrument were discussed .

将根管器械刃部假设为截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

D1.1 of the AISI Specification limits the maximum longitudinal spacing of connections to ... where smax = maximum permissible longitudinal spacing of connectors L= unbraced length of compression member rI = radius of gyration of I-section about the axis perpendicular to the direction in which buckling would occur for the given conditions of end support and intermediate bracing rcy = radius of gyration of one C-section about its centroidal axis parallel to the web.....

因此，AISI规范第D1.1节限定连接的最大纵向间隙为：，式中 smax =连接体允许的最大纵向间隙 L=抗压构件的自由长度 rI =工字钢对垂直于给定端承和中间肋条件下可能产生纵向弯曲方向的轴的回转半径 rcy =一段U型钢对其平行于筋的质心轴的回转半径。。。。。。。

The inner radius of univalence for some particular domains such as triangles, regular polygons and angle sectors have been obtained. Part estimations of inner radius of univalence for ellipses and rectangles have also been obtained.

对三角形，正多边形，角形区域，双曲线围成的区域的单叶性内径已经得到了精确的数值，对于椭圆，矩形的单叶性内径也得到了部分估计。

The results showed that pricking of ventriculus lateralis with syringe needle No.12 did not harm the cerebrium blood vessel within 6 mm radius of injection point and the injected sheep did not reveal harmful affection, but did when pricked out of the radius.

结果表明，在侧脑室进针点6mm半径范围内刺入不易伤及血管脑组织，注射羊不出现临床反应。否则反应剧烈而造成死亡

The radius chosen for the insert is important as this forms the outer radius for the winkle gate.

镶块的半径选择是很重要的，因为这部分形成了螺肉浇口的外半径。

The frictional heat energy was concentrated on the thermal effect layer with the thickness of 4 mm, The temperature gradient of contact surface is the highest, and decreased rapidly with the radius direction of the lining's groove. The temperature gradient and TEL's thickness increased with the increasing of the sliding speed. The temperature decreased rapidly with the radius direction and also with the increasing of center angle of the lining's groove. The sliding speed and distance are obtained under two sliding conditions when the lining fails, which supply the theoretical basis with the antislip design of friction hoist.

摩擦热量集中在热影响表面层，其厚度仅为4mm，接触表面温度梯度最大，沿绳槽径向迅速减小；温度梯度和热影响表面层厚度随相对滑速的增大而增大；衬垫温度沿径向急剧降低且随圆心角增大而减小；并得到了2种滑动工况下衬垫失效时的相对滑速和滑动距离，为摩擦提升防滑设计提供理论依据。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？