查询词典 radius of curvature
- 与 radius of curvature 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Spherometer ; Theory equation of sphere curvature radius ; Principle of Archimedes spiral.
球面曲率计;理论球径公式;阿基米德螺线原理
-
Based on measured surface topography in conjunction with theoretical analysis, the characteristics of surface during wear process are studied, and the asperity density and asperity curvature radius are given for the first time.
本文通过对缸套表面的实测和分析,研究了在磨损前后表面形貌的变化,并首次定量描述了微凸体密度、微凸体曲率半径及其沿高度方向的变化。
-
In chapter four, we prove that a complete open Riemmannian manifold with Ricci curvature negatively lower bounded is of finite topological type provided that the conjugate radius is bounded from below by a positive constant and its excess is bounded by some function of its conjugate radius.
第四章,我们证明了对于Ricci曲率具负下界的完备开Riemannian流形,当其共轭半径有正下界且它的Excess被其共轭半径的某个函数所界定时,它就有有限拓扑型。
-
4A series of factor such as the difference about the centre of figure and the shear centre, curvature radius, central angle is discussed.
4对曲线梁中的剪、形心位置的差异以及曲率半径、圆心角、预应力大小、摩阻损失等内力影响因素进行了分析。
-
Concave reflecting surfaces of spherical cap, paraboloid and hyperboloid of revolution are investigated with regard to the dependence of the levitation force on the section radius Rb and curvature radius R of the reflector.
针对球面、旋转抛物面和旋转双曲面三种形状的凹面反射端,系统研究了悬浮力与反射端截面半径R_b和曲率半径R之间的本征关系。
-
From the results, the profile error of NURBS interpolation is related to feed velocity and curvature radius in NC machine tools.
仿真结果显示,数控机床NURBS插补的轮廓误差与进给速度及给定曲线的曲率半径有关。
-
From the results,the profile error of NURBS interpolation is related to feed velocity and curvature radius inNC machine tools.
仿真结果显示,数控机床NURBS插补的轮廓误差与进给速度及给定曲线的曲率半径有关。
-
The curvature radius was derivated and the contact stress of the three-arc-sect isometric type surface was calculated through the elastic dynamics theory.
应用弹性力学理论,推导出接触点的曲率半径,对三弧段等距型面联接进行接触应力计算。
-
The maximum spherical-head cotter radius was obtained by computing the minimum curvature radios of the cavity surface, and the finish cutter locution data were computed using the equidistant offset surface method.
通过计算型腔曲面最小曲率半径,确定精加工时球头刀的最大允许半径;应用等距偏移曲面法计算出型腔曲面数控精加工刀位数据。
-
Rigid circular object 200 mm in diameter with a face having a convex spherical curvature of 300 mm radius with a 12 mm edge radius.
"Rigid circular object"(不知你们做的是什么东西)刚硬的环型物体的直径是200mm并带有一个面,这个面的突起球面曲率是300mm棱角半径为12mm。
- 推荐网络例句
-
With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.
随着死亡的吉他手Schuldiner接受主唱的职务,乐队在现实中树立了重要的影响。
-
But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.
不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐,因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。
-
Closes the eye, the deep breathing, all no longer are the dreams as if......
关闭眼睛,深呼吸,一切不再是梦想,犹如。。。。。。