查询词典 radius angle

Exterior Opposite Angle Area: According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方外部对角映射区向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

With a dip angle between 15° and 30°, the uplift of an obducted plate during continental collision is much higher, and able to form a high mountain. The uplift is greatest with a dip angle of 15°; whereas with a dip angle between 30° and 45°, the subduction depth of a plate is much deeper, and able to form a deep basin. The subduction depth is greatest with a dip angle of 45°. When the dip angle is equal to or greater than 75°, subduction and obduction movements between two continents become undistinguishable.

当断裂带倾角在15~30°时，两个大陆板块碰撞导致的仰冲板块一侧隆升高度相对更大，利于形成高大的山脉，其中以15°倾角对应的仰冲板块一侧隆升最高；当断裂带倾角在30~45°时，两个大陆板块碰撞导致的俯冲板块的俯冲深度相对更深，利于形成深陷的盆地，其中以45°倾角对应的俯冲陆块一侧俯冲最深；当断裂带倾角≥75°时，两个大陆板块之间的相对俯冲和仰冲作用变得不明显。

Experiments exposed that the inner flow of tooth space in the micro-channels was proved to be cycled flow after fully development. For the more, low velocity vortex cavities existed in the vertex angle and inner side of bend angle of straight angle micro-channel, while back flow only appeared in the internal side of bend angle of round angle micro-channel. It's easy to take place deposition in the low velocity vortex cavities, which is the main cause of blocking.

试验发现各类微通道齿间内流充分发展后是一种重复性流动，平角微通道顶角和转角内侧存在低速涡旋区，圆角微通道只在转角内侧出现回流，颗粒在低速涡旋区易发生沉积，是造成堵塞的主要原因。

For class III malocclusion there are no significant differences in Ls-SGo,Li-SGo,upper lip length , lower lip length , Cm-Sn-Ls, upper lip angle of inclination and Li-H line . There are significant differences in lower lip angle of inclination , mentolabial sulcus angle , upper lower lip angle , H angle.

安氏Ⅰ类错合患者与安氏Ⅲ类错合患者相比，在上唇突点到SGo距离、下唇突点到SGo距离、上唇长、下唇长、鼻唇角、上唇倾角和下唇突点到H线距这些测量指标上无显著性差异；其他表示唇部形态和位置的指标，下唇倾角、颏唇沟角、H角、上下唇角都有显著性差异。

Therefore, the electronic angle measurement also has code-degree angle measuring plate, grating-degree angle measuring plate and coding degree angle measuring plate combination, as well as the form of four kinds of dynamic measuring angle.

因此，电子测角也就有编码度盘测角，光栅度盘测角和编码度盘结合测角，以及动态测角等四种形式。

Germany TOP imported pneumatic angle seat valve types: internal thread pneumatic angle seat valve, welding-type pneumatic angle seat valve, flange type pneumatic angle seat valve, clamp-type pneumatic angle seat valve.

德国TOP进口过滤器类：法兰Y型铸钢过滤器、法兰Y型不锈钢过滤器、丝口不锈钢过滤器、蒸汽过滤器、天燃气过滤器、篮式直通过滤器、T型过滤器。

Shoulder joint angle and wrist joint angle changes have nothing to do with shooting distance; shoulder joint angle speed and wrist angle joint angle speed have nothing to do with shooting distance.

四、 不同距离投篮肩关节角度、腕关节角度变化与距离远近无关；肩关节角速度、腕关节角速度变化与距离远近无关。

Through the computer simulation,analyzing the effects of pitch angle,roll angle,roll angle rate,sink rate,angle of attack and side angle on the track of ejection and save life height .

为提供弹射座椅多模态控制输入参数选择的理论依据，通过计算机仿真，比较分析了俯仰角、滚转角、滚转角速度、下沉率、迎角、侧滑角等弹射启动时飞机状态参数对弹射轨迹和安全救生高度的影响。

Results show that the milling tool with rake angle 5°, clearance angle: 10°, helix angle: 45° and corner radius: 1 mm is tested on the surface integrity experiment.

实验结果表明，前角5°，后角10°，刀尖圆弧半径为1mm，铣刀螺旋角为45°的几何结构铣刀完成了表面完整性试验中。

Test and analysis show that, the distribution patterns of the tangent veloctiy fields in the big cone area and the small cone area, which are comprised of para-free vortex and para-forced vortex, are basically identical without a change of the radius of the boundary surface; with the increase of the angle of the small cone, the para-free vortex area decreases and the para-forced vortex area increases, and the emulsifiability of the fluid drips increases with the increase of velocity gradient; the tangent velocity increases with the increase of inlet flow, and the maximum tangent velocities of both the big cone area and the small cone area are 4.94 times of the inlet flow; and the maximum tangent velocity increases with the increase of the split ratio and with the radius of the boundary surface not changed.

试验分析表明，大锥段和小锥段切向速度分布规律基本相同，均由准自由涡和准强制涡构成，分界面半径rm没有变化；随着小锥角θ的增加，准自由涡区缩小，准强制涡区扩大，速度梯度增加会加大液滴的乳化程度；随入口流量增加，切向速度增大，经拟合得出大锥段和小锥段的最大切向速度均为入口流量的4.94倍；分流比加大，分界面半径基本不变，最大切向速度增加。

Now she was hungry and angry.She began to smoulder.

现在她又饿又气，她开始流露难以抑制的怒火。

You have placed our iniquities before You, Our secret sins in the light of Your presence.

诗90：8 你将我们的罪孽摆在你面前、将我们的隐恶摆在你面光之中。