查询词典 radiation flux

According to the studied results at present, the studied objects are mainly thin plate and beam about sound radiation mode, a method computed sound radiation mode of complex structure is presented in this dissertation, according to the results of the previous two chapter, a theoretical method to solve acoustical radiation mode and acoustical radiation efficiency of complex structure by boundary element method and acoustical radiation theory is posed, the acoustical radiation power is expressed as a Hermitian quadratic form, while the radiation modes is determined by general eigenvalue decomposing, and then the radiation efficiency is computed via the orthodoxy of radiation modes with regard to impedance matrix and average velocity matrix; lastly, the validity of the method is proved by pulsating sphere and radiating cube with analytical results. According to results of the form three chapter, the structure sound radiation sensitivity is studied in detail, the sound radiation power of structure can be expressed as positive Hermitian quadratic form, the sound radiation sensitivity can be expressed as two parts by partial differential with respect to design variable, which are sensitivity of boundary velocity and impedance matrix, combined with the theory of FEM and BEM, the structure sound radiation can be translated to the analysis of structure dynamic sensitivity and impedance matrix sensitivity. The theory posted in this dissertation is tested by the FEM software ANSYS and the software AAS programmed by author.

在前几章的基础上，通过结构声辐射的模态理论对结构的声辐射的机理进行了深入地探讨，针对目前声辐射模态的研究对象主要是简单的板和梁类结构，提出了一种计算复杂结构声辐射模态的方法，利用前两章研究所得的结论，将边界元方法与广义特征值的理论结合起来研究了复杂结构的声辐射模态与声辐射效率，先将结构的声辐射功率表示为一个正定的厄米特二(来源：ABb7C论文0909网www.abclunwen.com)次型，运用广义特征值分解求解了复杂结构的声辐射模态，然后利用声辐射模态关于阻抗矩阵与均方速度耦合矩阵的正交性，求解了复杂结构的声辐射效率，最后用具有解析解的脉动球与辐射立方体验证了该方法的有效性。

Ordinary solder materials, lead-free solder, the lead-free solder wire, solder paste, solder, the solder wire , high temperature tin, the low-temperature tin-line, lead-free tin-silver, the lead-free tin-silver line, low-temperature lead-free tin line, welding aluminum tin, the tin-aluminum welding wire, welding wire stainless steel tin, aluminum welding flux not stainless steel flux, environmental flux, welding of stainless steel, nickel, special aluminum solder, aluminum flux, aluminum brazing soft agent, paint remover, paint stripping powder (high-temperature paint stripping enameled wire a few seconds), copper aluminum welding, aluminum and aluminum welding, wire flux of new environmental protection (smoke-free and tasteless, non-volatile non-flammable) peaks of water-soluble flux, no-clean rosin flux, no-clean flux, thinners, cleaning agents, plate washer water , clean water machine, special purposes, such as water-soluble flux.

普通焊锡材料，无铅焊锡条、无铅焊锡线、焊锡膏，焊锡条、焊锡线、高温锡条、低温锡线、无铅含银锡条、无铅含银锡线、无铅低温锡线、焊铝锡条，焊铝锡线、焊不绣钢锡线、焊铝助焊剂、不绣钢助焊剂、环保助焊剂、焊不锈钢、镍、铝特种焊料、铝助焊剂、铝的软钎剂、脱漆剂、脱漆粉、铝铜焊接、铝与铝焊接、环保新型线材助焊剂(无烟无味、不挥发不易燃)水溶性波峰助焊剂、免清洗松香助焊剂、免清洗助焊剂、稀释剂、清洗剂、洗板水、抹机水、特殊用途水溶性助焊剂等。

Shadow effect can not be neglected for thermal analysis of spacecraft,Accroding to the angle between solar light and antenna orbit plane and its orbit location,analytical geometry method was used for accurately calculating solar radiation heat flux distribution of reflector surfaces.To analyze the temperature field under heat flux,the formulations of net radiation flux density between two gray elements and the net flux density of gray surface under external thermal flux were deduced.Based on the characteristic of space environment,the nonlinear temperature distribution in transverse direction of reflector shell self radiation were considered,the finite element formulations were given for orthogonal material layered shell by Galerkin method.A layered element including a inner heat source layer was proposed,and the finite element formulation expressed by DOF of the inner heat source layer were put forward with temperature and heat flux boundarys between adjacent layer.

单馈反射面赋形天线是未来星载天线发展的一个重要形式，分析了基于物理光学、几何光学和几何绕射理论的理想反射面辐射场；介绍了基于几何光学的反射面天线赋形方法；针对赋形过程中辐射场的快速分析要求，比较分析了基于物理光学的Fourier-Bessel和Jacobi-Bessel级数展开方法以及GB展开分析方法；利用GB展开快速分析方法在20GHz频率下对0.6m口径的天线进行赋形分析，实现中国大陆的30dB增益覆盖，通过数值计算研究了固定增益期望下的口径尺寸随频率的变化，以及频率为20GHz的不同尺寸天线赋形后的覆盖目标区域最大增益的变化情况。

CAS radiation technology services company in Shanghai of the Chinese Academy of Sciences, the Ministry of radiation technology company in Shanghai's technology subsidiary, and the Chinese Academy of Sciences radiation technology company in 1989 by the Chinese Academy of Sciences of Nuclear Science and Physical and Chemical led the organization of the Chinese Academy of Sciences, owned by high-energy physics Shanghai by the atomic nucleus, Lanzhou Modern Physics, Plasma Physics in Hefei, the Changchun Applied Chemistry, Hefei Chinese Scientific and Technical University jointly established a joint venture and technical input, built for the cable factory in Yantai, Changshu Cable Factory, Liyang Cable Factory, Huaian cable factory Electronic contracting, such as the establishment of a special radiation cross-linking cable production lines and a number of radiation center and computer and new materials production base, by the relevant State Council ministries and provincial and municipal leaders on the importance and recognition, that was the first national high-tech Enterprise units, radiation technology company in 2002 to reform the merger into a new high-tech companies, and the Shanghai Technology Services Division of the Department of independent legal entities and by relying on the Chinese nuclear radiation and high-tech base for the successful trial production of 200-nanometer tetrafluoroethylene Ethylene special engineering plastics ultra-fine powder, consisting mainly expected to add new type of dispersing agent, detergent, antioxidant Kangfu agent, the preparation of a motor vehicle and vessel efficient use of lubricating oil additives series.

中国科学院辐射技术公司上海服务部系原中国科学院辐射技术公司在上海的技术子公司，而中国科学院辐射技术公司是1989年由中科院数理化局核科学处牵头组织中国科学院所属的高能物理所，上海原子核所、兰州近代物理所、合肥等离子物理所、长春应用化学所、合肥中国科技大学共同合资并投入技术建立的，建成后为烟台电缆厂、常熟电缆厂、溧阳电缆厂、淮安电缆厂等承包建立了电子辐照交联特种电缆生产线和一批辐照中心和计算机及新材料生产基地，受到国务院有关部委和有关省市领导的重视和表扬，并被国家认定的第一批高技术企业单位，2002年辐射技术公司进行体制改革合并成新的高技术公司，而上海技术服务部系独立法人单位并依托中科院原子核所辐照基地的高新技术及试制成功的200纳米聚四氟乙烯特种工程塑料超细粉，以此为主料加上新型的分散剂、清净剂、抗氧抗腐剂等，配制成汽车用和船舶用的高效润滑油系列添加剂。

According to the invention, an exact flux-inducing current component of the rotational field machine is formed dependent on the flux-building current components formed, an amount of the machine flux vector formed, and on a value of the machine's main inductance. This component as the flux-inducing current component is compared to the flux-inducing current component set value.

按照本发明，根据所形成的磁通感应电流分量、所形成的一电机磁通向量绝对值以及一电机主电感的值可形成感应式电机的一精确的磁通感应电流分量，它作为磁通感应电流分量实际值与磁通感应电流分量额定值相比较。

When the gas flux is constant, the ratio of reduced resistance is improved with the increase of the water stream velocity. However, the relationship between the gas flux and the ratio of reduced resistance is more complex. When the water stream velocity is constant, if the gas flux is small in contrast, the effectiveness of reduced resistance is not obvious. But when the gas flux increased, the jetted gas will form """"archform"""" which will augment the shape resistance. In this condition, resistance could not be reduced and could even be increased, if the gas flux continues to be increased. So that there needs setting a baffle called step, which introduces the jetted gas into the turbulence boundary layer. In this case, the shape resistance may be fairly great. Besides, the waterline of model has also some effect on the ratio of reduced resistance, which acts on the size of wave. If waterline is deep, the wave could not affect the deployment of microbubble layer, so there is almost no effect on ratio of reduced resistance. However, the wave would affect distributing of microbubble layer under the model so that the gas could leak out from the two sides of model and directly affect the ratio of reduce resistance if the waterline is very small. Whether installing the dashplate or not has also the great influence on the effectiveness the ratio of reduced resistance. From the results of experiment, conclusion is that adding dashplate will greatly improve the effectiveness of reduced resistance.

当喷气量一定时，水流速度增大，减阻率提高；喷气量与减阻率之间的关系比较复杂，速度一定时，如果喷气量较小，减阻效果就比较差，但当喷气量增大的话，喷射出的气体就会形成一个&拱度&，增加了船模的形状阻力，在这种情况下最好采取断阶喷气，把气体引入到湍流边界层中，在这种情况下，船模的形状阻力比较大；船模的吃水对减阻率也有一定的影响，主要表现在波浪大小上，如果吃水较深，波浪影响不到微气泡层的分布，对减阻率不会造成太大影响，如果吃水较浅，波浪就会影响到微气泡层在船模底部的覆盖情况，可能会有部分微气泡从船模两侧泄漏，这样就直接影响到了减阻效果；是否安装压浪板，对减阻率也有较大的影响，从试验结果可以看出，在船模尾部加设了压浪板时，减阻效果明显得到改善。

The result makes clear, 2 class give urban sewage plant on the molecular quantity interval that organic owner should center the dissolvability in water water in kDa, and the content of organic matter compares hydrophoby the element of content big; of organic matter measures hydrophily interval distributings different organic thing shows water to accept filter film flux and hold back rate having distinct effect, the organic matter under molecular quantity 2kDa causes accept filter film to appear water flux attenuation bigger, organic matter is held back rate is minor, the organic matter that amounts to 57.2%; element to measure 10 ～ 100kDa causes accept filter film to appear water flux attenuation gentlier, organic matter is held back rate is older however highest the organic matter that amounts to 73.8%; to kiss scanty sex to differ shows water to accept filter film flux and hold back rate having distinct effect, classics is right of velar surface obstruction determine, confirm cause film to appear water flux and the main material that hold back rate change to be hydrophoby material, and the change that hydrophily material causes is minor.

结果表明，城市污水厂二级出水水中的溶解性有机物主要集中在kDa的分子量区间上，且疏水性有机物的含量比亲水性有机物的含量大；分子量区间分布不同的有机物对纳滤膜透水通量和截留率有着不同的影响，分子量2kDa以下的有机物引起纳滤膜透水通量衰减较大，有机物截留率较小，达57.2%；分子量10～100kDa的有机物引起纳滤膜透水通量衰减较平缓，有机物截留率却较大最高达73.8%；亲疏性不同的有机物对纳滤膜透水通量和截留率有着不同的影响，经对膜表面阻力的测定，证实引起膜透水通量和截留率变化的主要物质为疏水性物质，而亲水性物质引起的变化较小。

In the study of infrared radiation character, different species of tourmaline and Draviteoccurring in pegmatites from Hebei that are different in granularity and heattreatmenttemperature are chose for infrared radiation ratio testing. The result shows:The infraredradiation ratio of tourmaline powder is above 0.80 when the surrounding temperature is 20℃and the testing temperature is below 100℃;Schorl has a close infrared radiation ratio to Dravite,which is higher than Elbaite;No matter to Dravite or Schorl, as the content of ferric oxideincreases, the infrared radiation ratio decreases;tourmaline's size is smaller, its infraredradiation ratio is higher;after tourmaline is heat-treated under 800℃, its infrared radiation ratiodeclines;Dravite heat-treated at 800℃ has the highest infrared radiation ratio, 0.90;andDravite's structure suffers from destruction above 900℃ heattreatment, so its infrared radiationratio goes down.

在红外辐射特性的研究中，本文选择了不同种属电气石、不同粒度和不同热处理温度河北伟晶岩镁电气石进行红外发射率的测试，结果表明：在环境温度为20℃、测试温度为100℃下，电气石粉体红外发射率均在0.80以上；铁、镁电气石红外发射率相近，且大于锂电气石；不论在铁电气石还是在镁电气石中，随氧化铁质量分数的增加，红外辐射率下降；电气石粒径越小，红外发射率越高；电气石在低于800℃以下温度的热处理后，红外发射率下降，800℃热处理电气石红外发射率最高，为0.90，900℃以上电气石结构遭到破坏，红外发射率降低。

A prediction model has been proposed to deal with threshold voltage shift as a function of 1MeV neutron flux and gate oxide thickness, and to deal with room-temperature annealing of threshold voltage shift induced-by 〓Coγ as a function of electric field and gate oxide thickness. The commonness and individuality of MOS device degradation between hot-carrier effect and ionizing radiation were investigated. The dependence of substrate current, gate current and threshold voltage shift due to hot-carrier on gate oxide thickness were simulated with MEDICI-2D simulator. The photocurrents of PN junction and bipolar transistor were studied. Their transient responses on varied bias voltages, pulse durations and absorbed doses were simulated. The influences of NPN base width on base and collector photocurrents were investigated. We also studied 1MeV neutron displacement damage in PN junction, and calculated reverse current leakage under the neutron flux of 2. 67×10〓 per square centimeter. 3 The study of nondestructive screening method for MOS radiation tolerance A theoretical and experimental study of nondestructive screening methods for radiation tolerance of nMOS and pMOS were firstly fulfilled. We determined the informative parameters pertinent to the method and proposed how to deal with experimental data and verify obtained results statistically, as well as make the required steps for nondestructive screening. Based on the experimental data of 180 samples of discrete pMOS devices, the relation between sample quantity and correlation coefficient, screening equation, and other significant results were obtained from the threshold voltage shifts of pre-and post-irradiation samples.

二、分立器件电离和位移辐射损伤响应研究在国内首次开展了电离辐射引起的氧化层阈值电压漂移和退火理论研究，编程计算了1MeV中子引起的MOS器件阈值电压漂移与中子通量及栅氧厚度的关系，计算了〓Coγ光子引起的阈值电压漂移及退火的时效曲线与纵向电场和栅氧厚度的关系等，对评估MOS型集成电路电离损伤和加固方法研究，以及论文中开展的MOSFETs无损筛选方法研究奠定了基础；分析了MOS器件热载流子损伤效应与辐射电离损伤效应之间的异同性，利用二维模拟软件MEDICI-2D模拟了衬底电流和栅电流，在不同栅氧厚度下随栅压的变化曲线，计算了热载流子效应造成的阈值电压漂移，研究结果对当前存在的以热载流子效应研究取代电离辐射损伤实验研究的设想，具有重要的参考价值；开展了PN结和双极晶体管电离光电流研究，计算了不同偏压、不同辐射脉宽和不同吸收剂量下PN结光电流的瞬时响应，计算了不同辐射脉宽下NPN晶体管基极电流和收集极电流的瞬时响应，以及基区宽度对NPN晶体管光电流的影响，研究结果对双极器件抗电离辐射损伤响应及加固方法研究具有重要意义；在国内首次开展了器件位移损伤的理论研究，分析了辐射产生的缺陷对电性能的影响，计算了注量为2.67×10〓cm〓的1MeV中子产生的缺陷对PN结反向电流的影响。

In order to implement the algorithm, a linearization method is applied in an extremely short sampling cycle to calculate the increments of torque and flux magnitude, to derive the linear equation between the desired stator flux linkage vector increment angle and the increments of torque and flux magnitude, to derive the stator voltage vector reference and to determine the next position of the stator flux linkage vector.

算法的实现运用了线性化的方法，在一个极小的采样周期内，计算出转矩增量和磁通增量，以此推导出所需的定子磁链增量角与转矩增量及磁通增量两者之间的线性方程，进一步导出所需的定子电压矢量，并确定新的定子磁链位置。

You have to walk your own alk in this life.

次生中你必须走自己的路。

To start with, the thesis analyses ***ism in terms of the generic masculine words, word order and semantic derogation of women in greater detail.

论文首先从阳性词泛指，词序，词义的贬降等方面对英语中的性别歧视现象进行了详细的分析。