查询词典 rad

Rad and I, in particular, like to sleep all the time.

RAD和我，特别是我俩，喜欢一天睡到晚。

If you have experience about other RAD or languages, you will feel very familiar about the EPL.

如果你已经拥有了其它RAD 或者编程语言的经验，你将感觉到 EPL 非常熟悉。

EPL is an easy to use RAD environment for all levels of developer.

epl是一个易於使用的RAD环境，为各级发展。

Rad says he's almost babysitting sometimes because he has to remind me when I have stuff.

RAD常说自己有时像管小孩一样，因为他总是要提醒我，当我贪玩的时候。

Rad is advertising consultant and like many people, is in position that has behind the desk for most of the day.

Rad 是广告顾问。和许多人一样，他坐在办公桌前度过一天中的大部分时间。

EPL is an easy to use RAD environment for all levels of developer.

英超联赛是一个易於使用RAD数据通信公司的环境，各级开发商。

EPL is an easy to use RAD environment for all levels of developer.

EPL 是一款适用于所有等级开发者的简单易用的 RAD 编程环境。

Design one primer pairs for EphB2 receptor and one primer pairs for GAPD as internal control. The RT-PCR was used to analyze the expression of EphB2 receptor tyrosine kinase in gastric cancer, colon cancer, lung cancer, liver cancer, kidney cancer, spleen cancer and abdominal wall cancer. The results were analyzed using Bio-RAD UV transilluminator with Quantity One software system.

采用RT-PCR方法，分别检测胃癌、结肠癌、肺癌、肝癌、肾癌、脾癌、腹壁癌7种肿瘤组织及相应邻近正常组织中EphB2受体的表达，应用Bio-RAD凝胶成像系统及在Quantity One软件辅助下分析测定表达结果。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

Objective To evaluate the inhibitory effect of recombinant adenovirus rAd-MK-TNFα on cell growth of breast cancer in vitro.

目的 初步观察重组腺病毒rAd-MK-TNFα对乳腺癌细胞的抑制作用。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。