查询词典 queuing process

In chapter five, combined with the queuing theory and Markov process, the supply chain stochastic model is established, and the steady balanceable distribution is solved. The supply chain items are given and the different parameters'impact to these items and whole cost are analyzed. The optimal inventory control strategy is given at last.

第五章将排队论、马尔可夫过程与供应链模型相结合，建立了供应链随机库存模型，求解了平稳分布，给出了供应链指标，并分析了不同参数对指标和整体成本的影响，提出了最优的库存控制策略。

This paper studies that any system of queue can be transformed into Markovion queuing process and therefore,the solution can be obtained by Markovion Decision Programming′s value operation.

马尔科夫排队过程是马尔科夫决策规划的一个重要应用。

Based on the limited capacity system : queuing model,the process mechanized waste disposal in open pit mine are analyzed,a grey evaluation model in which the purchase cost,disposal capacity,operation cost and average useful life of vehicle are comprehensively took into account is constructed.

采用系统容量有限的：排队模型对露天矿机械化排土过程进行分析，构建了综合考虑购置费用、排土能力、运行成本以及车辆平均寿命等因素的综合灰色评价模型，以此确定汽车配置方案，并进行了实例验证。

Programme simulation: Simulate the process of the queuing according to queue model M/M/1, programming language C, the four steps such as data coming, waiting in queue, link service and data leaving.

程序模拟：本程序是以M/M/1为排队模型，使用C语言进行程序设计，通过数据到达、排队等待、链路服务、数据离开四个环节模拟了排队过程。

Via analyzes the present gateway s operating data at dissimilar parameter based queuing theory, Markoff process, embedded Markoff linker, the present thesis describes the problem that the present gateway has worse real time response when there are too much TCP sockets, the trait of the present gateway.

并运用排队论、马尔科夫过程及嵌入马尔科夫链分析了现存网关模型的各种运行参数，得到其特点以及在TCP连接过多的时候所存在实时性下降的问题。

Topics include the Poisson process, Markov chains, renewal theory, models for queuing and reliability.

工程随机过程介绍：泊松过程，马尔可夫脸，更新理论，排队模型和可靠性。

Firstly, according to the generalized router architecture, a variety of blockings during the transfer process are analyzed in this paper, and then an analytical router model which uses M/G/1/N queuing system is proposed. Secondly, an NoC performance analysis algorithm is presented,and the formulas for packet delay and saturated throughput are obtained.

首先从NoC路由器工作原理出发，对报文传输中的各种阻塞现象进行分析，建立了基于M/G/1/N排队系统的路由器模型；然后提出NoC网络性能分析算法，并且给出了传输延迟、饱和吞吐率等参数的解析表达式。

Carry on structure analysis to the spare parts first, understand its structure characteristics to choose suitable semi-finished product and the semi-finished product manufacturing of the reasonable a craft thus;Then the technique request of spare parts carries on analysis, understanding it each process superficial accuracy grade and the surface rough degree, make it process the fixed position in the process and clip a tight way in assurance inside the scope of economic accuracy, draw up the machine of spare parts to process craft process thus and further, choose each work preface to process equipments and craft material, the assurance slices to pare dosage and craft size, computing the man-hour of each work preface settle sum.

首先对零件进行结构分析，了解其结构特点从而选择合适的毛坯以及合理的毛坯制造工艺；再零件的技术要求进行分析，了解其各加工表面的精度等级以及表面粗糙度，使其在经济精度的范围内确定加工过程中的定位和夹紧方式，从而进一步拟订零件的机械加工工艺过程，选择各工序加工设备以及工艺装备，确定切削用量以及工艺尺寸，计算各工序的工时定额。

An engine cyclic variation model has been built by using the residual gas temperature for the n-th cycle as the input of the model, through constant pressure intake process, adiabatic compression process, constant volume combustion process, adiabatic expansion process, adiabatic blow down process and constant pressure exhaust process to approximate the thermodynamic processes in the cylinder, finally the residual gas temperature for the (n+1)-th cycle can be estimated.

基于循环间变动的排气温度建立了一个发动机循环变动模型。在这个模型中，第n个循环的排气温度作为模型的输入，通过定压进气过程、绝热压缩过程、定容燃烧过程、绝热膨胀过程、定容放热过程和定压排气过程来近似汽缸内的热力学过程，最后得出第n+1个循环的排气温度。

On the foundation of the reasonable fixed position, according to process the process in of be subjected to the dint appearance and clip the tight dint to arrange the principle, drawing up to clip the tight dint to arrange the project reasonablely;Passing the related calculation formula, cliping the tight dint size to carry on estimate towards process in the process, choosing the size structure to clip the tight motive component reasonablely, according to an oneself of work structure and processed requests and process to be characteristics by the dint in the process, choosing the design to clip the tight organization to guarantee by attain that the work piece positions accurate reasonablely, fast .

在合理定位的基础上，根据加工过程中的受力状态和夹紧力的布置原则，来制定夹紧力合理的布置方案；通过相关计算公式，对加工过程中夹紧力大小进行估算，来选择尺寸结构合理的夹紧动力元件，根据工件自身结构和加工的要求以及加工过程中受力的特点，来选择设计合理的夹紧机构以达到保证工件的定位的准确，快速。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。