查询词典 pump

Discharging ballast water with compressed air needs not to install ballast water pump unit that is necessary for pump discharging and simplifies ballast water pipeline system, reduces ship weight, improves the variable loading capacity of marine platform and finally promotes economic benefits.

采用压缩空气来控制与调节半潜式海洋平台或工作船舶的上浮及下潜，是借鉴潜水艇沉浮原理而设计的一种新型压载水排放模式，使用压缩空气排放压载水，免除了使用水泵排放所必须安装的压载水泵组并简化了压载水管系统，减少了船舶的自重，提高了海洋平台的可变载荷量，提高了经济效益。

The results show that energy can be extracted from pump beam when power density of Stokes beam is more than that of pump beam.

而且研究表明，随着斯托克斯光功率的增大，从抽运光中提取出的能量越多。

In theoretical research by introducing pump and cavity beam distribution functions, we obtain the input and output relationship under stable conditions and analyze the effect of the distance between the laser diode and crystal medium on the pump threshold and slope efficiency.

理论上通过引入端面泵浦光场与振荡光场的分布函数，得到稳态条件下输入输出特性，分析了泵浦光焦点位置对泵浦阈值及斜效率的影响和在不同泵光功率下的最佳光斑大小及透过率。

In the second chapter, the operating principle of solid-state laser is analyzed. Based on the model of four-level system and with the space-related rate equations, the space distribution of laser beam and pump beam, the threshold pump power, the output power, the slope efficiency, the input-output characteristic and the effect of space variables on the output character are studied. Also, the introcavity second harmonic generation theory is discussed.

第二章分析了固体激光器的工作原理，以四能级系统为模型，从与空间相关的速率方程出发，研究了泵浦激光和振荡激光的空间分布、阈值功率、输出功率与斜效率、LD端面泵浦固体激光器的输入输出特性及各空间变量对输出特性的影响，并讨论了腔内二次谐波产生理论。

Due to shrinkage of the beam waist of laser mode to match the pump beam, this laser can attain very high intensity in the pump region of gain medium and therefore most of its gain is depleted even by a standing wave.

由於雷射模会自动调整大小以符合泵浦光斑，雷射可以在被帮浦增益介质区域内达到很高的光强度，而使得大部分的增益被高强度的驻波消耗掉。

In fact, there is little pump of the fluid loss, which makes the operation of pumps can not achieve 100% efficiency, as these fluids are used to on both sides of bearing and gear lubrication, and the pump body is also not possible with no gap, it can not be so that 100% of fluid discharged from the export, so a small amount of fluid loss is inevitable.

实际上，在泵内有很少量的流体损失，这使泵的运行效率不能达到100％，因为这些流体被用来润滑轴承及齿轮两侧，而泵体也绝不可能无间隙配合，故不能使流体100％地从出口排出，所以少量的流体损失是必然的。

Nadequate flow of reasons: the actual lift pump lift more than allowed; speed does not support or belt slip, low speed; axial flow pump blade installation angle is too small; smoke way too high; at the end of valve, pipe and impeller Impeller partially plugged or defect; water possession of a serious leak.

SW卧式管道离心泵流量不足原因： IS、IR卧式单级单吸清水离心泵实际扬程超过允许扬程；转速不配套或皮带打滑、转速偏低；轴流泵叶片安装角太小；吸程过高；底阀、管路及叶轮局部堵塞或叶轮缺损；出水管漏水严重。

Nadequate flow of reasons: the actual lift pump lift more than allowed; speed does not support or belt slip low speed; axial flow pump blade installation angle is too small; smoke way too high; at the end of valve pipe and impeller Impeller partially plugged or defect; water possession of a serious leak.

SW卧式管道离心泵流量不足原因：IS、IR卧式单级单吸清水离心泵实际扬程超过答应扬程；转速不配套或皮带打滑、转速偏低；轴流泵叶片安装角太小；吸程过高；底阀、管路及叶轮局部堵塞或叶轮缺损；出水管漏水严重。

The cooling pump is belt-driven by the combustion engine crankshaft, resulting in a direct coupling of engine and cooling pump speeds.

受驱动方式的限制，风扇和水泵转速依赖于发动机的曲轴转速，不能根据发动机的不同工况自动调节。

Engaged in spinning mold design, stamping die design (blanking die design, punch die design), and the spinning class product design (mainly the automobile belt pulley, water pump wheel, booster pump pulley, etc.), and rendering product process chart, product assembly diagram, right products, process analysis and process improvement, proficient in CAD, are familiar with PRO / E 3D modeling and design aspects of the work.

从事旋压模具设计，冲压模具设计（落料模具设计，冲孔模具设计）以及旋压类产品造型设计(主要是汽车皮带轮，水泵轮，助力泵带轮等)，绘制产品工序图，产品组装图，对产品进行工艺分析以及工艺改善，精通CAD，熟悉PRO/E三维造型设计等方面工作。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。