查询词典 pump-out

The double entry back-to-back pump was selected for the HPOTP in the SSME in order to increase the shaft speed by 2 and stay within the tip speed limit, while maintaining the required total inlet flow area.

双入境背对背泵被选定为hpotp ，在ssme ，以增加轴的速度 2和留在尖端的车速限制，同时保持所需总入口流量面积。

The 200,000-foot head requirement for the SSME HPFTP dictated a three-stage centrifugal pump with the impellers operating at 2,000 ft/sec tip speed.

该20.0万英尺的头部的规定，为ssme hpftp取决于三个阶段的离心泵叶轮经营二零零零英尺/秒的速度提示。

Two holes were used for the inlet/outlet gas lines and a third was used to introduce the reductant, 20% aqueous tin(I1) chloride (Baker Inc., No. 3980-01, Phillipsburg, NJ) in 10% HCl, using a peristaltic pump.

两个孔用于进出气孔，第三个孔用于引入还原剂。20%水和三氯化锡溶于10%盐酸中，用搅拌泵搅拌。

In order to solve above problems, a frequency conversion timing unit for screw pump well and an automatic control system were developed.

针对地面驱动螺杆泵抽油杆断、脱频繁及单井提液调整参数难以控制等问题，开发了螺杆泵井的变频调速装置及自动控制系统。

Main production tapered roller bearings, cylindrical roller bearings, automotive clutch bearings, automotive bearing direction, automotive wheel bearings and wheel hub unit, the center support bearings, automotive water pump at the same time can produce bearings, thrust roller bearings, non-grinding bearings, stamping bearings, etc..

主要生产圆锥滚子轴承、圆柱滚子轴承、汽车离合器分离轴承、汽车方向机轴承、汽车轮毂轴承及轮毂单元、中心支架轴承，同时可生产汽车水泵轴承、推力滚子轴承、非磨轴承、冲压轴承等。

Large inbuilt thrust bearing in the pump head ensures that no thrust is transferred to the motor.

大内在的推力轴承在泵头部确保没有主旨是转移到汽车。

The pressure differential is less than 10 kgf / cm2 small pump, thrust bearing can be used.

对于压差小于10千克力/cm2 的小型泵，可以采用止推轴承。

Nevertheless, single-stage pump is not one hundred percent of the balance, it also uses a thrust bearing.

纵然如此，单级泵也不是百分之百的平衡，所以还采用止推轴承。

The use of CAXA entity software provides the effectual security for 3D physical design of the turning attachment of emulsion pump three-throw crankshaft,in assembling and animation simulation,reflecting the work principle of scale division,examining interference and installing、debugging、maintaining tongs.

应用CAXA实体设计软件对乳化液泵三拐曲轴车床夹具的三维结构设计、装配及动画模拟，反映分度车床夹具的工作原理，检查分度机构的设计是否合理及干涉情况，为安装、调试、维护夹具提供有效的技术保障。

Frost/defrost performance of a three-row fin staged heat pump evaporator.

风冷热泵冷热水机组结霜工况下运行特性的实验研究。

The Porsche Owner: But it's my car!

可，这是我的车呀。

LOX_83}{Oh, another bunch of wackos.

{LOX_83}{呃，又一群怪人。