查询词典 pump rod

The author did the tracking test to four kinds of exist using energy-saving motors of sucker rod pumps,compared and analysed the tested data on the wattless losses,wattful power,single consume to output of fluid,energy-saving rate and average system efficiency of pump units.

跟踪测试了孤东油田目前在用的4种有杆抽油机节能电机，利用科学、准确的实测数据，从无功损耗、有功功率和产液量单耗、节电率、抽油机平均系统效率等方面进行了对比分析。

Main products are piston, bettery, carburator assy, flashier, ignition switch, shock absorber, fuel cock, steering lock, starting coil, clutch cable, speedmeter cable, gear shaft, kick shaft, con-rod, engine block, chain, fuel tank, bulb, gear, pointer, water pump, relay, bearing, rear hub, clutch firber, sprocket, lever assy, back mirror, etc.

主导产品：活塞及活塞环，电瓶，化油器，闪光器，点火开关，减震器，油开关，车头锁，点火线圈，导线，齿轮，连杆，汽缸，链条，油箱盖，灯泡，转向灯，水泵，继电器，轴承，轮股，离合器片，链轮，把手，后视镜等我们生产和销售各种摩托车和汽车配件，并且在不断地开发新产品。

Crank bearing is the key component of crank connecting rod mechanism of emulsion pump and the damageable part during power transmission.

曲柄轴承作为乳化液泵曲柄连杆机构的关键部件，也是动力传递过程中极易损坏的薄弱环节，曲柄轴承的磨损失效是高压大流量乳化液泵的主要失效形式。

Ogrammable logic controller meets the specifications to guarantee the safe operation of equipments.Crank bearing is the key component of crank connecting rod mechanism of emulsion pump and the damageable part during power transmission.

曲柄轴承作为乳化液泵曲柄连杆机构的关键部件，也是动力传递过程中极易损坏的薄弱环节，曲柄轴承的磨损失效是高压大流量乳化液泵的主要失效形式。

The solution: find the plunger adjustable arm or gear from the speed control rod protruding ears slot prolapse, should re-open the fuel pump is installed correctly; also check whether the cross-slot wear and tear is too large, if found dead in parked for seca column position, should be demolition of repair or replacement parts; injector should be able to check the plunger is serious wear and tear, deputy returned to the oil valve gasket is worn; demolition injector, check whether the coupling of needle stuck in the closed position, needle and the injection hole Does burning, according to test results even to repair or replace parts.

解决办法：发现柱塞调节臂或齿轮凸耳从调速拉杆槽中脱出，应拆开喷油泵重新正确安装；同时检查叉槽是否磨损过大，如发现柱塞卡死在停供位置，应拆卸进行修复或换新件；喷油无力应检查柱塞副是否严重磨损，回油阀垫圈是否磨损；拆卸喷油器，检查针阀偶件是否卡死在关闭位置，针阀与喷油孔是否烧损，根据检查结果进行修复或更换偶件。

The connecting rod d is driven by a crank on the engine axle and works the condenser air-pump.

连杆D是驱动曲柄对发动机轴及工务局冷凝器的空气泵。

Has good lubrication properties, so that fuel injection pump, engine block and connecting rod to reduce the wear rate, and enhance life.

具有较好的润滑性能，使喷油泵、发动机缸体和连杆的磨损率降低，增强使用寿命。

The total building cold load is 1440KW, the cold heat source is chooses two refrigeration quantities is the 852KW half seal screw rod type air source heat pump unit.

总建筑冷负荷为1440KW，冷热源是选择两台制冷量为852KW的半封闭螺杆式空气源热泵机组。

Other amenities include stainless-steel hardware, flush rod holders, a transom door, locking hatches to access an in-deck 14 cubic feet insulated fishwell with a macerator pump and a pair of insulated stowage wells, with provisions to convert one of the compartments into a deep, rounded 40 gallon livewell.

其他设施包括不锈钢的硬件，冲水杆持有人， transom门，锁定舱口进入一，在甲板上一十四立方英尺绝缘fishwell与macerator泵和一对绝缘装载水井，与条文，以转换其中的隔间成深，四舍五入四十加仑

With regard to the question how to cut the helical camber of screw-pump and spiral rod drilling tool in the field of petroleum machine and chemical machine, this paper firstly puts forward the cutting method how to apply the milling with non-instantaneous-pole envelope principle with plate milling cutter in our country.

本论文针对石油、化工机械领域螺杆泵、螺杆钻具转子的螺旋曲面切削加工问题，在国内首次提出了应用盘铣刀的无瞬心包络铣削加工方法。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。