查询词典 protective coating

Natural insolation experiment and human accelerating aging experiment data on the fluorocarbon coating and other FEVE fluorocarbon resin coating to be used for national palaestra "bird nest" are introducted, and comparison is made to explain the main cause for the performance difference on different types of fluorocarbon resin coatings.

介绍了"鸟巢"国家体育场用氟碳涂料与其他FEVE型氟碳树脂涂料在海南的天然曝晒试验与人工加速老化试验数据，并进行了对比分析，阐述了各种类型氟碳树脂涂料在耐老化性方面存在差异的主要原因。

Also, the influences of the ratio of rosin to paraffin wax in coating, and of coating weight on the nutrient release rate were discussed.

分析了松香与石蜡的配比、涂层量对包膜尿素养分释放速率的影响。

This particular line incorporates world-class complete vehicle cathode electro-coating technology. The integrated body and chassis frame is subject to degreasing and phosphatization pretreatment and then to cathode electro coating, which significantly improves paint membrane adhesion and corrosion resistance of complete vehicles, brings the products up to quality standards and make complete vehicles resistant to corrosion for more than 10 years.

该生产线采用国际先进的整车阴极电泳技术，车身和底盘车架一体整车经过脱脂、磷化前处理，再进行阴极电泳处理，大大提高整车漆膜附着力及整车耐腐蚀性能，满足产品质量要求，整车的防腐可达十年以上。

One aspect is the coating method of phosphor, which influences the LED's color temperature and range of available color properties, so,phosphor coating in manufacturing process must be uniform in thickness.

荧光粉的涂抹方式对白光LED的发光分布与色温的均匀度影响很大，荧光粉厚度较厚的位置黄光产生较多，色温会较低，因此在芯片上形成的涂抹层必须是均匀。

My company registered capital of 2,000,000 U.S. dollars, the annual design production capacity of 60,000,000 , production use of lead-free glass of possession, use of advanced three-color phosphor powder coating process water and coating processes, implementation on the real meaning of green environmental protection product, strict product quality, reaching the National standards.

我公司注册资金200万美元，年设计生产能力6000万支，生产使用无铅玻璃明管，三基色荧光粉采用先进的水涂粉工艺及涂膜工艺，实现真正意义上的绿色环保产品，产品质量严格把关，达到了国家标准要求。

Secondly, It states the package process of White LED in detail and discusses the following aspects: One aspect is the coating method of phosphor, which influences the LED's color temperature and range of available color properties, so,phosphor coating in manufacturing process must be uniform in thickness.

接着根据白光LED所存在的问题，对白光LED的封装工艺和原材料的选择搭配进行改进，在本文中白光LED有两种封装方式，一种是支架式封装形式，一种是大功率LED的封装形式。

The influence of different assembled condition such as assembly method, concentration of zirconium source and pH value on the effectiveness of assembly were evaluated via DSC-TG, FT-IR, Uv-vis and SAXRD et al. It showed that the assembly effectivness of uncalcined 3 Si/Zr_10# sample was best.c The optical characteristic, which including light-conduction in infrared band and polarity in visible band, of dip-coating film and membrane assembled zirconia after processing parameters of assembly optimized were observed via FT-IR and Uv-vis. The polarity was characterized by polarizing angle through calculation from light-transmittance, light-reflectance and fresnel coefficient. qualitative analysis showed that the polarity of Si/Zr_10 # dip-coating film assembled was best.d Adopting zirconium oxychloride as zirconium source, CTAB as template, employing different CTAB adding sequence, two mesoporous zirconia samples were prepared. The template effect of two samples was discussed. It showed that the effect of the sample which CTAB adding sequence was same as mesoporous silica film was better. The light-conduction in infrared band of these samples was also studied, which offered comparison to the polarity of zirconium dioxide assembled within mesopore.

结果显示：组装条件优化后的uncalcined 3 Si/Zr_10#厚膜样组装效果最好，其组装液对应的pH值最利于该锆源离子模板交换组装； c选用FT-IR、Uv-vis对组装条件优化后纳米氧化锆/介孔氧化硅厚膜、纳米氧化锆/介孔氧化硅薄膜包括红外导光性、可见光区内的偏光性在内的光学特性进行了分析，其中偏光性以膜层透光性、反光性及菲涅耳系数计算出的偏振角即布儒斯特角表征，定性分析显示，Si/Zr_10#ZrO_2/介孔氧化硅厚膜偏光性最好； d以氧氯化锆ZrOCl_2·8H_2O为锆源，CTAB为模板剂，采用不同的模板剂加入顺序，探索性地制备两介孔氧化锆样，分析了两介孔氧化锆样的模板效果，得出模板剂加入顺序同介孔氧化硅薄膜时介孔氧化锆样的模板效果较好，并分析了所得样品的导光性，为锆氧粒子引起的附加光学特性分析提供了参考和对比。

This is the rule of thumb for anybody who is looking for a second hand binocular with maximum performance: If it is a Porro, it should have been made after 1980 (availability of multi layer coating), if it is a roof prism, then not earlier than 1990 (phase-shift coating).

所以对二手镜子光学表现有要求的买家而言，这里有一条基本原则：要是买保罗镜，最好是1980年以后的，如果买屋脊镜，就别买1990年以前的。

In order to solve the problem of potassium iodide Ioss in microelements premixed material and find out the optimal coating method,residual rates of potassium iodide of pretreated feeds using different kinds of coating s in different treating times were determined in the paper.

为解决微量元素预混料中碘化钾损失的问题，采用不同包被物对碘化钾进行预处理，测定碘化钾在不同处理下一定时间的留存率，从而找出较优的包被处理方法。

The electrochemical analysis results show that the polarization potential of gradient coating was obviously lower than that of the non-gradient coating electrode.

电化学测试结果表明，与非梯度镀层相比，梯度镀层的极化电位在各电流密度条件下都显著低于非梯度镀层电极。

You can snipe the second and third union leaders from this position.

您可以鹬第二和第三工会领袖从这一立场出发。

Aiming at the currently shortage of XML streams quality detecting, this paper proposes a new forecasting method of XML streams quality by least squares support vector machines, which is used the method of XML keys' vector matrix as windows, and vector product wavelet transform to multilevel decompose and refactor the XML streams series, that can fulfill real-time checking demand of XML quality, and ensure constraint, consist- ency and integrality. For even more adapting net load, it proposes a control strategy by weight and adaptive adjustment to ensure XML streams quality.

针对当前XML数据流质量检测存在的不足，提出构建XML键的矢量矩阵作为窗口，利用矢量积小波变换多级分解与重构XML数据流，再结合最小二乘支持向量机对XML数据流质量进行预测的一种方法，满足XML数据流质量重构时实时检测的要求，保证XML数据的约束性、一致性与完整性；为了更好的适应网络负载，采取加权与自适应窗口调整等调度策略充分保证XML数据流的质量检测。