查询词典 protective coating

An AlTiN ceramic coating was deposited on the surface of biomedical Ti6Al4V alloy by High Ionic Pulse technology. The properties of biofriction and wear of AlTiN coating in simulated serum lubrication at 37℃ were investigated and compared with that of non-coating Ti6Al4V alloy.

采用高度离子化脉冲工艺在医用钛合金Ti6Al4V表面制备AlTiN涂层；在摩擦磨损试验机上测试了涂层在37℃的模拟人体生理血清液润滑条件下的摩擦磨损性能，并与之和未经涂层的Ti6Al4V合金作比较。

The product offers a perfect solution for the problem of color durableness of mineral coating and makes mineral coating really coexist with nature, really a revolution of coating industry.

改性后的硅酸钾不但具有更为良好的化合性，同时与各种氧化无机色素能良好相容，彻底解决了矿物涂料的色泽问题，使得矿物涂料真正与自然共存，成为涂装行业的一次革命。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wire The relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wireThe relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

In order to research the influence of polyaniline on acrylic anticorrosive coating, the polyaniline/acrylic anticorrosive coating that the mass rate of emeraldine base form of polyaniline in coating was 0%, 1.5%, 3%, 5%, 10% were prepared, and theirs anticorrosive performance in 3.5% NaCl solution was studied by Tafel and EIS.

为了研究本征态聚苯胺对丙烯酸涂层防腐性能的影响，制备了本征态聚苯胺质量分数分别为0%，1%，3%，5%及10%的聚苯胺／丙烯酸防腐涂层，应用Tafel极化曲线和电化学阻抗谱方法对比了其在3.5% NaCl溶液中的防腐性能。

The results show that, there is a white zonal area between the AZ61 and Al-alloyed coating, which indicates that a good metallurgical bonding is obtained. The coating shows typical hypoeutectic structure. Due to lots of Mg17Al12 phases in Al-alloyed coating, the corrosion resistance of AZ61 magnesium alloy is increased obviously.

结果表明，涂层与基体形成了扩散白亮带，实现了较好的冶金结合；涂层具有亚共晶组织的特点；大量的Mg17Al12相存在于涂层表面是耐腐蚀性能提高的主要原因。

The results show that the composite coating is metallurgically bonded to the substrate and the microstructure is fine and uniform. The hardness of the composite coating is up to 400 HV, which is 2.5 times that of the substrate. Under room temperature and oil lubrication condition, the sliding wear tests indicate the friction coefficient and weight loss of the composite coating are smaller than those of substrate. The worn surface of the composite coatings is much smoother than that of the substrate, without grooves and crater.

结果表明，复合材料涂层与基体形成良好的冶金结合，微观组织细小、均匀；复合材料涂层硬度达400HV，约为基体的2.5倍；在室温油润滑条件下，滑动磨损试验表明复合材料涂层摩擦系数和失重均小于基体，磨损表面划痕较浅且平滑，无明显的犁沟、粘着、剥落现象；激光表面合金化显著提高了材料的耐磨性。

Alumina sols of different content were prepared by using Al3 as precusor, water as solvent, nitric acid as peptizer, ethylacetoacetate and polyvinylpyrrolidone as modified menstruum. We used dip-coating method and spin-coating method prepared of alumina films on the plane glass and used dip-coating method and rising liquid method inside the wall of the fiber.

以仲丁醇铝为前驱物、水为溶剂、硝酸为胶溶剂、同时加入乙酰乙酸乙酯和聚乙烯吡咯烷酮作为改性剂制备了不同浓度的氧化铝溶胶用提拉法和旋覆法在平板玻璃上镀膜，同时用提拉法和液面上升法在石英毛细管内壁上镀膜。

In the deep processing of agricultural and food products, there are some key technological problems of system design on the domestic traditional reelable vacuum aluminium coating system, including mass process parameters, bad process duplication, unstable production quality caused by complex operation, and high equipment failure rate. A newly developed reelable vacuum aluminium coating system with 1500 mm-wide thin plastic films was designed with high vacuum technology in order to satisfy the vacuum aluminum coating of more than 1500 mm-wide, such as polyethylene terephthalate, oriented polypropylene, polypropylene cast film, polyvinyl chloride.

为满足农产品及食品深加工中1500 mm幅宽以上的聚脂薄膜、定向聚丙烯薄膜、聚丙烯流涎薄膜、聚乙烯薄膜的真空镀铝，针对国内卷绕蒸发式真空镀膜机设备存在的工艺参数多、工艺重复性差、操作复杂、产品质量不稳定、设备故障率高等问题，采用高真空技术研制了宽幅卷绕蒸发式高真空镀膜机。

Because of having surplus weld reinforcement height and irregular seam form as well as the influences of polyethylene raw materials and coating process, the quality problems of ununiformity in thickness of 3PE coating and coating thickness reduction on helical seam occur.

由于螺旋埋弧焊管存在焊缝余高超高和焊缝形貌不规整等现象，加之聚乙烯原材料及涂敷工艺等因素的影响，会使三层PE防腐涂层出现涂层厚度不均、焊缝处涂层减薄等质量问题。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48