查询词典 process plate

A three-dimensional finite-element model, which includes plate, punch, die and holder pad, is established to simulate the drawing process based on the characteristics of the square box part.

根据方盒形件的特点，本文建立了包括板料、凸模、凹模以及压边圈在内的三维有限元分析模型。

Through analyzing on the upper part of oil box and the design of the drawing die structure,the characteristics of the low melting point alloy were described,and discussed the characteristics of low melting point alloy die and the application in plate materical drawing process, the attention problems of die design were pointed out.

以分析油箱上体工艺特性和设计其低熔点合金拉伸模具结构为例，论述了低熔点合金材料的特点，介绍了低熔点合金模具的特点及其在板料冲压工艺中的应用，指出了模具设计应注意的问题。

The stamping process and the structural design of a progressive die for the side plate of a condenser was analyzed in detail,presenting the layout design and the main points in design of the progressive die.

介绍了冷凝器侧板的冲压工艺与级进模结构设计，针对冲压工艺分析、排样方案设计以及级进模设计要点进行了具体的阐述和总结。

The formation reasons of microstructures with three different characteristics were discussed by simulating filling and solidification process for the plate die casting.

经过平板压铸件充型及凝固过程的数值模拟，探讨了上述不同特征表层组织形成的原因。

With a spring installed inside table, you can move it up and down, and it can adjust the pressure, swing it before and after by eccentric wheel and pulley. The swing margin is about 12 degrees. The platform was installed in the L-plate and can correct center to ensure die non-deformation and roundness in polishing process.

工作台里面安装弹簧一根，可以上下移动，并可任意调整压力，利用皮带轮和偏心轮带动，使前后摆动，摆动幅度约12度，而工作台被安装在 L 型拖板上可以任意地对中心，确保在抛光的过程中，使模具不变形及圆度。

Stainless steel stick, dish circle and steel plate, stainless steel 喉 hoop, soft tube, not mark to press diagram to process

不锈钢棒、盘圆及钢板，不锈钢喉箍，软管，非标按图加工。

The screw rolling gear is a kind of high- efficiency cutter used to process screw thread, however in the course of processing, there is a problem that the arbitrary multiple- head number is difficult to be divided with dividing plate.

滚丝轮是一种高效率的螺纹加工刀具，但在被加工的工程中，存在着任意头数很难用分度盘分度的问题。

With development of the industrial control system,programmable logic controller is widely used in dividing shear of Baosteel Heavy Plate Mill,especially in the fields of the main motor control of dividing shear ,collection and analysis of PDA data,control of pinch rolls, adjustment control of knife gaps,shearing process control,etc.

随着工业控制系统的不断发展，可编程控制器在宝钢分公司厚板厂定尺剪系统中得到了全新的应用，尤其在定尺剪的主电机控制、PDA数据采集和分析、夹送辊控制、剪刃间隙调整控制、剪切过程控制等方面得到了应用。

Research results:The research and demonstration were made on construction order, diversion, grouting process, grouting materials and grouting parameters for the transverse hole and bottom plate of treated underground river as well as supporting structure, prevention and drainage of water for the tunnel during treatment of underground river in order to make the measures feasible.

研究结果：在暗河处理过程中，对处理暗河的横洞、底板的施做顺序、导流、注浆工艺、注浆材料及注浆参数、隧道的支护结构、防排水等提出可行的处理措施。

Also analyzes the mold of the main components (such as punch and die and dump devices, drawing punch, slates, Punch plate, etc.) design and manufacturing, stamping equipment selection, punch-gap adjustment and establishment of a vital parts machining process.

还具体分析了模具的主要零部件（如凸凹模、卸料装置、拉深凸模、垫板、凸模固定板等）的设计与制造，冲压设备的选用，凸凹模间隙调整和编制一个重要零件的加工工艺过程。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新