查询词典 process plate

The adoption of CTP technology not only greatly simplifies platemaking process short seihan time (a set of color plate time required for conventional seihan time only 1/3), and reduce the phenomenon of dot gain, so that hihglights and darkened parts of mesh point loss and a significant reduction in the power grid, which improves the ability to copy from.

采用CTp技术，不仅大大简化了制版工艺，缩短了制版时间（出一套彩色版材所需时间仅为传统制版时间的1/3），而且减少了网点增大现象，使高光与暗调部位的网点丢失与并网大为减少，提高了印版的复制能力。

For the example of the ploughshare, this paper described the deformation rule, process and the special-plate type forgings.

本文以机引犁铧为例，阐述了异形板片类锻件辊锻成形时的变形规律、工艺及模具设计要点。

The corrosion resistance of nanocrystalline nickel wascompared with that of Watt nickel and polycrystalline nickel plate in thesolution of NaCl and HCl by the methods of static soak and polar anodicpolarization curve and the mechanism of corrosion was analyzed. Themechanical property of nano- crystalline nickel was evaluated by macroscopictension and the microscopic process of deformation and fracture was observedby in-situ tension test under TEM.

在此基础上，采用差热分析、XRD 及 TEM 等手段研究纳米晶体镍的热稳定性；利用静态浸泡、阳极极化曲线等方法研究纳米晶体镍的耐蚀性能；采用宏观拉伸的方法考察了纳米晶体镍的力学性能，并用 TEM 原位拉伸法观察纳米晶体镍形变与断裂过程的微观过程。

Prepress operations and pressroom measurement tool-a printing plate measuring instrument, the autocollimating density gauge and auto-scan system for use on the G7 the smooth implementation of proof-to-print process is critical.

印后操纵和印刷车间丈量东西——印版丈量仪、不合平密量仪和被迫扫描编制的搁置差G7 proof-to-print历程的挫折奉行至关次要。

The process calculations such as layout chart of punching die for locatized plate, punching pressure, pressural center and etc.

简述了定位板冲模的排样图、冲压力及压力中心等工艺计算，设计了冲孔、锪孔、落料级进模。

To measure and control the dot area in plate-making and printing process is an important subject to improve print quality.

检测并控制制版印刷过程中的网点面积，是提高印刷质量的重要课题。

Excellent reflow process window can make it good CuOSP plate welding, and printing of all sizes are a good combination of points.

出色的回流工艺窗口使得其可以很好的焊接CuOSP板，与各种尺寸的印刷点均有良好的结合。

Research results:The analysis process of frame bridge with skew angle has been given by use of MIDAS.We obtained the outcomes from two models and the difference between results with 2D rigid frame and 3D space model of thick plate element.

在分析斜交框架桥时，通常有2种计算方法，一种是取1 m宽度，按斜交跨度的刚架来分析，另一种是按厚板理论，用空间有限元对斜交框架进行三维分析。

Roll-up: The process of inking a plate with a roller.

这个盆子是镀金金属的，所以不太值钱。

So we designed a adaptive synchronizing controller based on hereinbefore hardware environment: first a small magnitude reference signal r is outputted to system through the signal card (to ensure that the vibrating system works in a linear state), and this signal is sent to the moving coil of vibrator through the power amplifier, so vibration is produced through electromagnetic induction. Secondly the vibration signal can feedback to the data acquiring card in the servo system through the acceleration sensor on the Vibroseis reactor M〓 and the base-plate M〓, then the computer can get the current vibrating state y〓 of the coil of vibrator according to the feedback information from the data acquiring card, and give a real time comparing between the current state y〓 and the reference output y〓 of the set-in reference model with current reference input being r , then regulates the correlative controlling parameters according to the error e〓=y〓-y〓 till y〓→y〓, finally normal signal sweeping begins with a certain phase fixed. Meanwhile a synchronization signal for seismic signal record is sent to seismograph from synchronization signal outputting component in the Vibroseis system to perform the controlling process of synchronization of sweeping phases.

为此，我们基于以上的硬件环境设计了一个自适应同步控制器：首先通过信号发生卡对系统输出小幅度的参考信号r(从而保证振动系统工作处于线性状态)，信号通过前置放大器、功率放大器等送到激震器动圈，并通过电磁感应产生振动，振动信号通过可控震源激震器反应块M〓和基板M〓上的加速度传感器反馈给伺服系统中的数据采集卡，工控计算机根据采集卡的反馈信息，获取当前激震器动圈的振动状态y〓，并实时地将该状态与内置的参考模型在当前参考输入r下的参考输出y〓进行辨识，再将两者输出误差e〓＝y〓-y〓对系统的有关控制参数进行调整，直至y〓→y〓，最后在经过某一固定的相位后，开始信号的正常扫描过程，与此同时，由可控震源系统的同步信号输出部件向地震仪送出一地震信号记录同步信号，进而完成扫描相位同步控制过程。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。