查询词典 process plate

The process of preparing a printing surface for electrotyping by first engraving on a wax-coated metal plate.

蜡模，蜡刻制版法一种通过先在涂蜡金属板上''。'刻字'。''来准备电版印刷''。'平面'。''的工序

In the business card printing and membership card manufacturing process, with water roll has to come into contact with the surface of the plate, offsctdruckereien use water out ink will be emulsibility emulsive, is a small amount of ink by water roll, to water roll, conspiracy water roller slot passed into the bucket, so no doubt about it to say that the water in the water roll chemiluminscent set must be kept clean, from oil pollution.

在制卡和会员卡制作过程中，着水辊都要接触印版表面，胶印使用水就决定了油墨将被乳化，被乳化的少量油墨通过着水辊、传水辊、串水辊传递到水斗槽里边来，所以说，水辊的水绒套必须保持清洁，不沾油污。

The factors affecting end curl of plate and sheet in rolling process were researched by the cross experiment, which include the upper roll diameter, the lower roll diameter, reduction, angle of entrance and velocity of roll rotation.

用正交实验方法对影响板带材轧制头部翘曲的因素进行了铅板轧制实验研究。影响因素有上下轧辊直径比、压下率、导入角和轧辊转速。

PCFK series of pairs of counter-reversible hammer crusher is a new crushing equipment, mainly by knock-on effects to broken materials, broken process in general is this: the material falling into the break in the world, imported high-speed rotation of the hammer impact face was against the entrance of the adjustable crusher tooth wear plate, for the first time broken, broken after the particles basically the same material evenly into the main break, the secondary primary crushing, crushing in the main chamber has been uniformly The material was re-kinetic energy particles from the hammer, high-speed rushed back inside the jagged cavity lining was broken, due to the special lining sawtooth-shaped structure.

PCFK系列可逆双反击锤式破碎机是一种新型破碎设备，主要是靠冲击作用来破碎物料的，破碎过程大体是这样的：落下的物料进入破世界进口后，遇到高速旋转的锤头冲击而被打击到破碎机进口处的可调耐磨齿板上，进行首次破碎，破碎后颗粒基本相同的物料均匀的进入主破碎内，进行二次主破碎，在主破碎腔内已被均匀的物料颗粒从锤头再次获得动能，高速冲向反击腔内部的锯齿形衬板而被破碎，由于衬板特殊的锯齿形结构。

The Process Research and Effect Comparison Between the Dissolve Mould Foundry of the QT400-15 Finger Plate Sandal and Conventional Sand Mould Foundry

在生产 QT40 0— 1 5指形板座的实践中，应用普通砂型铸造和消失模铸造，产生了两种不同的效果，经比较认为消失模铸造具有其独特的优势，同时简述了消失模铸造工艺对生产该产品的技术关

Based on the exergy transfer equations, exergy transferring in the steady heat conduction process are calculated for the infinite plate at the first type boundary condition, and two results are compared when conductivity is stable and changed with temperature in this paper.

利用一维稳态传递方程，对平壁在第一类边界条件下的一维稳态导热过程的传递做了数值计算，并就导热系数为定值与变值的两种计算结果进行了比较。

Firstly, according to the mechanism and kinetics model of coagulation, the process of coagulation dynamics of folded plate flocculator is analyzed and flow pattern has an important impact on flocculation effect too.

首先，结合絮凝机理及絮凝反应动力学模型，分析了折板絮凝池絮凝动力学过程，得出水流状态对絮凝效果具有重要影响。

As one of main matching plant of Fustian automobile,we supply the support process of over 30 varieties of components and arts including footplate hanging unit assembly and clutch pressure plate unit assembly and etc for all sorts of automobile and farm truck.

公司作为福田汽车的主要配套厂之一，为其各种汽车、农用车提供踏板吊挂总成，离合器压盘总成等30余种零部件的配套加工。

Moldflow software was used for searching for optimal parameter of forming process of ABS gusset plate by simulating real condition.

通过模拟真实注射条件，应用Moldflow软件对 ABS扣板注射成型工艺参数进行了优化分析，得出影响注射成型顺利进行的主要因素，并模拟制定出扣板注射成型的最佳注塑压力、锁模力、模具温度、熔体温度、注塑时间、保压压力、保压时间和冷却时间。

In order to meet the requirements of process, the magnetic hanging girder bridge plate piler was designed.

为满足工艺要求，设计了电磁挂梁桥式垛板机。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。