查询词典 process furnace

Metal corrosion in sulfuric aeid edw point is a common and very serious harm go the corrosion forms, in a wide range of production in all aspects of life, especially in some specific process unit operation equipment middle.low-temperature corronsion dew point in the general industrial rurnace, boiler, fuel saving edvices, air preheater, heat exchangers, tower refrigeration systems, dust, garbage incineration furnace, sintering furnace flue and chimney acid plant and the wind tunnels of hypothermia sife, yes containing gurnace flue and chimney acid plant and wind tunnels of hypothermia site, yes containing acidic gases produced by the condensation of cold treatment from the local cold drinks along with the liquid in the device, lesding to a very serious material corrosion.

该下载资料由本站会员上传，如果侵犯了您的权力，请通知我们，将立即删除！摘要金属材料的硫酸露点腐蚀是一种常见的，危害十分严重的腐蚀形式，广泛的发生在生产生活的各个方面，尤其发生在一些特定的过程单元操作设备中间。低温露点腐蚀一般发生在在工业加热炉、锅炉、燃料节省器、空气预热器、热交换器、塔顶冷凝系统、除尘器、垃圾焚烧炉、烧结炉、烟道，烟囱及酸厂的引风管道等的低温部位，是含酸性的气体经由该产遇冷冷凝下来的冷饮液局部地随着于设备上，从而造成对材料极严重的腐蚀。

The delayed cooking equipment process mainly consists of heating furnace, coke drum, fractionating tower and some other simple units. Since the heating, coking and fractionating are focused on this study, heating furnace, coke drum and fractionating tower are established and the suitable solution way is selected.

延迟焦化装置流程主要包括加热炉、焦炭塔、分馏塔和其他一些简单单元设备，本论文分别对加热、焦化、分馏过程进行研究，建立了加热炉、焦炭塔、分馏塔模型并选择适宜的解法。

Combustion temperature measuring technology is one of the basis of combustion theory and technology development. The measurement of furnace 3-D combustion temperature distribution is very effective for extensively researching for combustion process in furnace.

燃烧温度测试技术是燃烧理论和技术发展的重要基础之一，炉膛三维燃烧温度分布测量对于全面研究炉膛燃烧过程是十分有效的。

The paper presents the performance of smelting process of copper scraps by imported Kaldo furnace on the basis of 300 kt/a copper production in Guixi Copper Smelter,JCC as well as advantages and disadvantages of such Kaldo furnace type for treating scraps.

介绍江铜贵冶年产30万t铜冶炼项目引进卡尔多炉处理废杂铜冶炼工艺的情况，并介绍了卡尔多炉这种炉型处理废杂铜的优缺点。

The campaign of induction furnace is lower because 10t main frequency furnace uses of acid refractory liner that is corroded by liquid iron and basic slag under the working condition of high temperature and full load and abr aded in the process of charging cold burden.

10t工频感应炉炉衬原采用酸性耐火炉衬，在高温满负荷工作状态下，受铁液及碱性炉渣侵蚀，加冷料过程中受机械磨损，造成感应炉炉龄低。

The paper introduced the process of applying 10MW induction heating furnace to compensate temperature of welded tube before reducing mill,which is controlled by a micro-processor Compared with oil-heated,gas-heated and coke-fired furnaces,the heating furnace occupies a small area and operates agility.

介绍了英国钢铁公司科比厂在焊接钢管减径前，采用一台由微处理器控制的 10MW 感应加热炉进行温度补偿。

In accordance with the austenization microstructure transformation principle,to compare the process characteristics of open-fire furnace ,muffle and semi- open-fire furnace with stainless steel tube.

根据奥氏体化组织转变原理，比较明火炉和马弗炉及不锈钢管式半明火炉的工艺特点，分析和探讨明火炉的优势和工艺特性。

For reducing the fault ratio of shaft ore-roasting furnace, based on the analysis of the fault mechanism and combination of case-based reasoning and variables prediction, an intelligent fault prediction approach is proposed for the shaft furnace roasting process.

为降低竖望炉焙烧过程的故障发生率，基于故障机理的分析，将过程参量预报与案例推理技术相集成，提出了竖炉焙烧过程的智能故障预报方法。

The furnace for the test is the oil-burner that is designed and produced by ourselves. The whole test process is undertaken in the modeled standard temperature curve. The result of the test demonstrates that the properties of the furnace are stable and convenient for use.

火灾试验使用的试验炉为自行研制的燃油火灾试验炉，全部的试验是在模拟标准升温曲线的基础上进行的，试验结果表明炉子性能稳定、使用方便。

Analyze the effect of tapping hole clay production process and blast furnace smelting on blast furnace tapping hole under the condition of high strength smelting; compare the result of tapping hole clay with waterless tapping hole clay by using them and discuss the tendency.

记述了攀钢四高炉在高强度冶炼的条件下，炮泥生产工艺和高炉冶炼对高炉出铁口的影响因素，通过分析炮泥的使用效果，并将有水炮泥与无水炮泥作了比较，对其发展趋势作了一点探

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。