查询词典 problem of contact

Compared with the initial value problems of scalar conservation laws with smooth flux function, the global weak entropy solutions for the initial-boundary value problems of scalar conservation laws with weak discontinuous flux function include the following new interaction types: a rarefaction wave collides with the boundary and is absorbed compltetely or partially by the boundary; a rarefaction wave collides with the boundary and the boundary will reflect a contact or non-contact shock wave; a contact or non-contact shock wave collides with the boundary and is absorbed by the boundary; a contact or non-contact shock wave collides with the boundary and a new non-contact shock will rebound from the boundary simultaneously or later.

与具有光滑流函数的单个守恒律的初始值问题相比，具有弱间断流函数的单个守恒律初边值问题的整体弱熵解中包括下列新的相互作用类型：稀疏波碰到边界并被边界部分或全部吸收；稀疏波与边界相撞，边界反射出一个接触或非接触激波；接触或非接触激波碰到边界并被边界吸收；接触或非接触激波与边界相撞，边界同时或稍后反射出一个新的非接触激波。

In addition, total wheel/rail contact calculation with divided rail outline method are raised. Under the condition of considering the displacement, bouncing, yaw, roll of wheelsets and displacement, bouncing, roll of rails, minimum gap between rail and wheel were calculated by the trochoid method and divided rail outline method, we can easily judge totally real contact states of the wheel/rail such as normal one-point contact, nonnormal one-point contact, two-point contact and wheel complete lift. Wheel/rail normal forces in the two contact point are respectively calculated by nonlinear Hertz contact theory, and then, result of simulation more close to reality on actual track.

另外，提出了轨廓分区法全面计算轮轨接触状态法，在考虑轮对的横移、浮沉、摇头、侧滚和左右钢轨的横移、浮沉、侧滚的条件下，可全面地分别计算左右侧轨顶和轨侧区域与车轮的最小轮轨间隙量，以此来判断轮轨的真实接触状态：正常的一点接触、非正常的一点接触、两点接触和车轮完全悬浮，并根据非线性赫兹接触理论分别求得两接触点处的轮轨法向力，从而使仿真结果更接近于车辆在实际线路上的运行状态。

The gap element method is proposed in the paper for two kinds of problems, which include contact problem and gap joint problem. Elasticity contact problem falls into the category of unknown boundary value problems. It follows that the contact area and contact conditions or states can never be determined without special mathematical analysis, which is a very difficult work. The boundary conditions of the contact surfaces are deduced.

文中给出了间隙元法在空间可动部件接触问题中的应用，推导了其几何边界条件和力学边界条件，利用虚功原理推导了含间隙元弹性接触问题的有限元方程式，给出了其数值解法的迭代步骤，并指出了利用间隙单元进行分析的特点。

First, this article introduced 2 grade of rotary kiln principle of work and the equipment, to rolled the circle mechanics behavior to carry on the analysis, proposed - rolled the circle - under roller's rotary kiln overall modelling based on the tube body - kiln liner - big tooth ring, to rolled the circle - under roller's contact stress to carry on the finite element analysis the method, and obtained rolled the circle contact stress the size and the distribution rule, finally indicated that rolled the circle contact stress mainly to have two main peak values and the sudden change in one week, appeared is rolling the circle and the under roller contact area; Then, rolls the circle the stress to regard as is the principal stress unknown plane stress test, the use quite mature modern test technology, proposed rolls the circle stress test the principle and the plan, and to rolled the circle the stress to carry on the scene test, the stress which the scene test analysis result and the finite element analysis calculated has compared, had proven the whole method modelling's finite element analysis method's rationality and rolled the circle - under roller contact stress the result accuracy; Finally, uses ANSYS APDL the re-development technology, in view of 2 grades of rotary kilns, rolled the circle - under roller contact stress the overall finite element analytic method to carry on the re-development.

首先，本文介绍了2档回转窑工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-窑衬-大齿圈-滚圈-托轮的回转窑整体建模，对滚圈-托轮的接触应力进行有限元分析的方法，并得到了滚圈接触应力的大小和分布规律，结果表明滚圈接触应力在一周内主要存在两个主要的峰值和突变，都出现在滚圈与托轮接触区域；然后，把滚圈的受力看成是主应力未知的平面应力的测试，利用比较成熟的现代测试技术，提出了滚圈应力测试的原理和方案，并对滚圈的应力进行了现场测试，现场测试分析结果与有限元分析计算出的应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力的结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Wenzhou Juxing Silver Contact Co, Ltd is a domestic expert electrical contact material company which integrates production, research and sales ***** is located at Wenzhou, a place full of natures treasures and never change our route-exploit and ***** are six categories and thousand of products, such as rivet contact, rocker contact, composite belt, powder metallurgy contact, profiled composite contact, silver alloy wire etc.which cover low voltage electrical appliances, electronics, communication, consumer electrical products, military, and so on.

温州市巨星银联系有限公司是国内专家电触头材料的公司，集生产，研究和销售*****位于温州，一个充分的性质县宝藏和永远都不会改变我们的路线，利用和*****六类和1000的产品，如铆钉接触，摇臂联系，复合带，粉末冶金联系，异型复合接点，银合金丝etc.which包括低压电器，电子，通讯，消费电子产品，军事，等等。

To make the design and manufacture of the spring contact more standardized,the authors analyzes the causes of such problem as contact resistance fluctuation of the spring contact in use,and proposes a corresponding structure design method of spring contact.Comparison and analysis are performed for the properties of cobalt bronze and beryllium bronze,and a standardized design scheme of spring contact is presented,in order to support the design,manufacture,operation and maintenance of GCB/GIS.

为了使弹簧触头结构的设计制造更加标准和规范，笔者对近两年来弹簧触头在使用中出现的接触电阻波动等问题的原因进行了分析，提出了相应的结构设计方法，对钴铜丝和铍青铜的材质性能进行了比对和分析，并给出了弹簧触头设计的规范化方案，对GCB/GIS的设计、制造、运行维护有一定的指导意义。

In studies of interaction among pile, platform that above it and surrounding soil, this paper employ the concept of plate element to simulate the loading character of platform, and employ the concept of solid element to simulate the character of pile and soil, using the finite element method after understanding the geometry properties of pile, soil and the platform. Analyzing the loading properties of the three entities above and their deformation, this paper also employ a special element, Penalty Element. The introduction of penalty element of this kind has served to guarantee the join harmony of displacement between solid element and plate element, thereby effectively resolving the join problem between platforms, pile that support it and surrounding soil.Considering significant property difference between pile material and its surrounding soil, there may be much shear stress on their contact interface produced under vertical load, thus causing displacement or fission. Therefore it is necessary to adopt one special constitutive law of this kind of contact interface, which can reflect its feature of loading and deformation thoroughly. On the basis of the deformation feature and constitutive laws of some contact interface obtained by Zhang Dongji and people concerned through some single-shear experiments on contact interface between structure and soil, this paper employ one pile-soil three-dimensional constant thickness contact interface model to simulate the " slide" taken place on the interface between pile and its surrounding soil. With this kind model, this paper has also created one finite element model, which can be applied to perform finite element calculation and analyze the pile-loading feature, and deduced its element stiffness matrix.

在承台-桩-土共同作用中，考虑桩与承台的几何特性，采用有限元方法，用实体单元模拟桩土，用板单元模拟承台，更具体地分析桩和承台的受力特性和变形，而且还采用罚单元—既实体单元与板单元之间连接必须满足变形协调条件，来有效地解决了承台与桩土的连接问题，且在桩土共同作用中，由于桩体结构的材料性能与周围土层性质相差较大，在竖向荷载下有可能在其接触面上产生较大的剪应力从而导致错动或开裂，因此，为了充分反映桩土接触面上的受力及变形特征，应采用一种桩土接触面特有的本构关系，即利用张冬霁等人关于结构与土体接触面单剪试验所得到的接触面变形特征及其本构关系，引入桩-土三维等厚度接触单元来模拟桩与桩侧土之间的&滑移&，在此基础上建立可用于桩基承载性状分析的有限元计算单元模型，并推导出了各单元的刚度矩阵。

A numerical calculation program is written up for the various solution methods in this paper and the program is being used in various aspects of inverse problem of environmental hydraulics, including inverse problem in reverse process of one-dimensional unstable diffusion, inverse problem in reverse process of convection-diffusion, inverse problem for the dispersion coefficient in water quality model, The inverse problem of coefficient identification for nonlinear Boussinesq equation, parameter identification inverse problem for water quality model, the inversion of parameter of BOD-DO water model, the inverse problem of the source of convection-diffusion, identification of the steady-state permeability for two dimensional isotropic medium, two-dimensional steady inverse problem of convection-diffusion and parameter identification inverse problem for two-dimensional parabolic equation, etc.

对本文提出的各种算法，编制了数值计算程序，并把它应用于环境水力学反问题诸多领域，包括污染物一维非恒定扩散逆过程反问题，对流扩散方程逆过程反问题，河流水质纵向弥散系数反问题，非线性Boussinesq方程反问题，河流水质多参数识别反问题，BOD-DO水质模型参数反演问题，对流—扩散方程源项反问题及二维恒定各向同性介质渗透系数反问题，二维定常对流——扩散方程及二维抛物型方程参数控制反问题等。

Firstly, the paper introduced the working principle and device of the two-pass grate-rotary kiln and had an analysis method of mechanics of the tyre. We have put forward the finite element analysis of the contact stress of the tyre-roller based on the whole construction mode of shell-kiln liner-large gear-tyre-roller of the rotary kiln and obtained the strength and distributing rule of the tyre's contact stress. The research shows that within one week the contact stress mainly lies in two leading peak value and catastrophe which appear at the contact zone of the tyre and supporting roller. Then we regarded the tyre's stress as the test of unknown plane stress of principal stress. Utilizing mature and modern testing technology, we raised the testing principle and scheme of tyre stress and then had a on-the-spot test of the stress. Comparing the analysis result of the test with the one calculated from the finite element analysis, it proofed the rationality of finite element analysis method of integral modeling and the correctness of the contact stress result of the tyre and roller. Finally, for two-pass of similar rotary kilns, using the ANSYS APDL re-development technology, carried on the re-development about the overall finite element analytic method of thecontact stress of tyre-roller.

首先，本文介绍了2档回转窑的工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-滚圈-托轮的回转窑整体建模的有限元分析法，来对滚圈-托轮的接触应力进行有限元分析与计算，得到了滚圈接触应力的大小和分布规律，并求得滚圈外中内圈节点的主应力；其次，把滚圈的受力看成是主应力未知的平面应力的测试，利用现代测试技术，提出了滚圈主应力测试的原理和方案，并对滚圈的主应力进行了现场测试，现场测试分析结果与有限元分析计算出的主应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档同类回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

The difference of mean intraocular pressure among readings obtained with the lens in place, after lens removal and lens reinsertion were not statistically significant in bandage contact lens group and in low myopic contact lens group. But the high myopic contact lens group showed statistically significant difference of mean intraocular pressure obtained with the lens in place, after lens removal and lens reinsertion. In addition, the intraocular pressure readings measured immediately after myopic contact lens reinsertion revealed poor reliability.关键词 Tono-Pen , Soft contact lenses

我们把受测者分为三组：低度近视组，高度近视组和配戴治疗性隐形眼镜组，每组分别以受测者未戴隐形眼镜时的眼压做基准，而以其他三种情形的眼压分别与之比较，结果发现以Tono-Pen测量低度近视组和配戴治疗性隐形眼镜组的眼压值可信度较高，但是戴上隐形眼镜之后马上测量的眼压值较不准确，而高度近视组的测量值则出现变异的现象，可信度较低。

Salt is good, but if the salt becomes flat and tasteless, with what do you season it?

14：33 盐本是好的，盐若失了味，可用什么叫它再咸呢？

He reiterated that the PLA is an army of the people under the leadership of the Communist Party of China.

他重申，人民解放军是在中国共产党领导下的人民军队。