查询词典 principal stress

The plastic deformation induced due to cyclic rotation of principal stress axes alone can be in the same magnitude as that due to shear with fixed principal stress axes. 2 The volumetric strain due to shearing of cyclic rotation of principal stress axes is found to be composed of a reversible dilatancy component and an irreversible dilatancy component. The former is characterized by its reversibility and is independent of past shear history, the latter by its irreversibility increases with the increase of cycle number yet its increase rate decreases with its accumulation. 3 The obvious non-coaxiality between directions of the principal stresses and principal strain increments is found and its degree depends largely on the change of shear stress component. 4 The intermediate principal stress has considerable effects on the deformation behavior of sands in the condition of cyclic rotation of principal stress axes. The accumulation rate of the irreversible dilatancy component increases with the increase of the intermediate principal stress parameter.

具有初始各向异性的砂土在纯应力主轴循环旋转排水条件下的主要变形规律为：①纯应力主轴循环旋转可产生与应力主轴固定单调剪切处于同一数量级的塑性变形；②纯应力主轴循环旋转引起的剪切体变包含可逆性剪切体变分量和不可逆性剪切体变分量两部分，其中可逆性剪切体变分量在一周内可完全恢复，基本与应力历史无关；不可逆性剪切体变分量随循环周数的增加呈单调增加，且增加速率随其自身累积值的增大呈减小趋势；③应变增量主轴与应力主轴之间的非共轴现象显著，且在一周内具有分段性；④中主应力对应力主轴循环旋转条件下砂土的变形特性有重要影响，不可逆性剪切体变分量的累积速率随中主应力系数的增加而增加。

The main achievements could be summarized as follows.1. The basic stress-strain characteristics and related physical mechanisms for sands under cyclic rotation of principal stress axes were investigated based on three kinds of drained tests including fixed principal stress axes, cyclic rotation of principal stress axes with magnitudes of principal stresses kept constant, and cyclic changes of principal stresses in both their axes and magnitudes. The main deformation behavior of sands with inherent anisotropy under cyclic rotation of principal stress axes with magnitudes of principal stresses kept constant was obtained in the following.

本文从试验研究、规律分析、数学建模和工程应用四个方面，对应力主轴循环旋转条件下砂土的变形特性进行了较为深入的研究，取得了如下主要研究成果：(1)基于对饱和砂土进行的主轴固定单调剪切、纯应力主轴循环旋转以及主应力幅值与应力主轴耦合循环变化的三类完全排水试验成果，分析和揭示了应力主轴循环旋转条件下砂土的基本变形规律，并探讨了其受力变形的内在机理。

The measurement results show that the general characteristics of the present crustal stress field of the project area are as follows: the horizontal principal stress is the maximum principal stress, and the preferred orientation of the maximum horizontal principal stress is NW-WNW, the maximum principal stress of surrounding rocks of the plant buildings and high-pressure branch tunnel area is generally 14.5±0.5 MPa and the minimum principal stress is 9±0.5 MPa; the dead oad-bearing capacity of surrounding rocks is 10—14 MPa; and the surrounding rocks are essentially impermeable at high pressures of 8—10 MPa.

测量结果表明，工程区现今地壳应力场的总体特征为：水平主应力为最大主应力，最大水平主应力的优势方向为NW-NWW向；厂房和高压岔管区围岩的最大主应力值一般为14.5±0.5MPa，最小主应力值一般为9±0.5MPa；围岩自身的抗载强度一般为10～14MPa；在8～10MPa高压力作用下围岩基本不透水。

In order to support and perfect the professionalization of principals, a series of systems are needed, which include the systems of principal's qualification, principal's selection, principal's responsibility, principal's term, principal's rank, principal's training, principal's supervision, principal's yearly salary and principal's withdrawal.

实现校长的专业化地位，必须有外部的一系列制度来加以支持与完善。这些制度与措施是校长资格制度、校长选拔制度、校长负责制度、校长任期制度、校长职级制度、校长培训制度、监督校长制度、校长年薪制度、校长退出制度。

First, this article introduced 2 grade of rotary kiln principle of work and the equipment, to rolled the circle mechanics behavior to carry on the analysis, proposed - rolled the circle - under roller's rotary kiln overall modelling based on the tube body - kiln liner - big tooth ring, to rolled the circle - under roller's contact stress to carry on the finite element analysis the method, and obtained rolled the circle contact stress the size and the distribution rule, finally indicated that rolled the circle contact stress mainly to have two main peak values and the sudden change in one week, appeared is rolling the circle and the under roller contact area; Then, rolls the circle the stress to regard as is the principal stress unknown plane stress test, the use quite mature modern test technology, proposed rolls the circle stress test the principle and the plan, and to rolled the circle the stress to carry on the scene test, the stress which the scene test analysis result and the finite element analysis calculated has compared, had proven the whole method modelling's finite element analysis method's rationality and rolled the circle - under roller contact stress the result accuracy; Finally, uses ANSYS APDL the re-development technology, in view of 2 grades of rotary kilns, rolled the circle - under roller contact stress the overall finite element analytic method to carry on the re-development.

首先，本文介绍了2档回转窑工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-窑衬-大齿圈-滚圈-托轮的回转窑整体建模，对滚圈-托轮的接触应力进行有限元分析的方法，并得到了滚圈接触应力的大小和分布规律，结果表明滚圈接触应力在一周内主要存在两个主要的峰值和突变，都出现在滚圈与托轮接触区域；然后，把滚圈的受力看成是主应力未知的平面应力的测试，利用比较成熟的现代测试技术，提出了滚圈应力测试的原理和方案，并对滚圈的应力进行了现场测试，现场测试分析结果与有限元分析计算出的应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力的结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Firstly, the paper introduced the working principle and device of the two-pass grate-rotary kiln and had an analysis method of mechanics of the tyre. We have put forward the finite element analysis of the contact stress of the tyre-roller based on the whole construction mode of shell-kiln liner-large gear-tyre-roller of the rotary kiln and obtained the strength and distributing rule of the tyre's contact stress. The research shows that within one week the contact stress mainly lies in two leading peak value and catastrophe which appear at the contact zone of the tyre and supporting roller. Then we regarded the tyre's stress as the test of unknown plane stress of principal stress. Utilizing mature and modern testing technology, we raised the testing principle and scheme of tyre stress and then had a on-the-spot test of the stress. Comparing the analysis result of the test with the one calculated from the finite element analysis, it proofed the rationality of finite element analysis method of integral modeling and the correctness of the contact stress result of the tyre and roller. Finally, for two-pass of similar rotary kilns, using the ANSYS APDL re-development technology, carried on the re-development about the overall finite element analytic method of thecontact stress of tyre-roller.

首先，本文介绍了2档回转窑的工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-滚圈-托轮的回转窑整体建模的有限元分析法，来对滚圈-托轮的接触应力进行有限元分析与计算，得到了滚圈接触应力的大小和分布规律，并求得滚圈外中内圈节点的主应力；其次，把滚圈的受力看成是主应力未知的平面应力的测试，利用现代测试技术，提出了滚圈主应力测试的原理和方案，并对滚圈的主应力进行了现场测试，现场测试分析结果与有限元分析计算出的主应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档同类回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Applied with test of potted plant and measurement absorbency for study response of the contents of photosynthetic pigments of slash pine's half-sib under water stress. There are 7 families comparison with general slash pine. The contents of photosynthetic pigments are mensurated under feebleness water stress while soil water content is 55% to 60% and moderate water stress while soil water content is 35% to 40% and heavy water stress while soil water content is 20% to 25%. The test result indicate that either water grads or families of chlorophyll and chlorophyll a and chlorophyll b and Chla/Chlb and carotenoid and Caro/Chl are mighty notable difference. The Chl and Chla and Chlb and Chla/Chlb little drop from normal soil water to initial water stress. Then drop obvious with increased water stress. The Caro and Caro/Chl little drop firstly from normal soil water to initial water stress,then up in metaphase water stress,after drop in evening water stress. The Chl and Chla and Chlb and Chla/Chlb and Caro of slash pine'half-sib are over general slash pine. The Chl and Chla and Chlb and Chla/Chlb and Caro of 464 and 1027 are over average value of slash pine's half-sib under water stress. The Caro/Chl of 609 and 46 are over average value of slash pine's half-sib under water stress.

为研究湿地松半同胞家系光合色素对水分逆境的响应，采用盆栽试验和吸光度测定方法，以湿地松普通种子为对照，测定了七个湿地松优良半同胞家系在弱度水分胁迫（土壤相对含水量为55%~60%）、中度水分胁迫（土壤相对含水量为35%~40%）和强度水分胁迫（土壤相对含水量为20%~25%）条件下的光合色素，对湿地松优良半同胞家系在不同水分胁迫条件下的光合色素进行了研究，结果表明：无论是不同水分梯度还是不同家系水平，Chl、Chla、Chlb、Chla/Chlb、Caro、Caro/Chl均有极显著差异；从正常水分至水分胁迫初期Chl、Chla、Chlb、Chla/Chlb稍微下降，后随着水分胁迫程度的加深下降较快，从正常水分至水分胁迫初期Caro、Caro/Chl先稍微下降，胁迫中期上升，胁迫后期下降；所有半同胞家系的Chl、Chla、Chlb、Chla/Chlb、Caro高于普通种，在水分胁迫条件下家系464、1027的Chl、Chla、Chlb、Chla/Chlb、Caro高于家系的平均水平，家系609、46的Caro/Chl值高于家系的平均水平。

As to'Cabemet Sauvignon'and'Queen of Vineyard', which belong to the'West Europe Cultivars Group', no obvious decline of Fv/Fm was found in their potted plants even under severe drought stress. Their photosynthetic abilities also greatly recovered after rewatering, i. e. no serious photodamage was formed in these cultivars under drought stress. Between them, the φPSⅡ of 'Queen of Vineyard'under severe drought stress was much lower than that of'Cabernet Sauvignon', which suggested that the light use efficiency of the former was much lower than the latter under severe drought stress. The potted plants of'Autumn Royal'and'Rizamat' sustained high Fv/Fm and φPSⅡ before moderate drought stress, but seriously declined under severe drought stress, which indicated that these cultivars had a weak resistant ability to extreme drought stress. A hybridized cultivar of Vitis vinifera L. and V. labrusca L.,'Red Double Taste', its Fv/Fm and φPSⅡ expressed mild decline along drought stress grade.φPSⅡ of'Red Double Taste'was the highest among seven cultivars under severe drought stress condition, which might closely connected with its high photorespiration activity. Another new cultivar,'Red Globe', and a rootstock,'1103Paulsen', the Fv/Fm and φPSⅡ of their potted plants declined markedly under slight drought stress, which suggested that they held a weak ability to defend against photoinhibition.

西欧品种群的赤霞珠和葡萄园皇后，其盆栽苗的Fv／Fm直到重度干旱胁迫下仍没有明显的降低，且复水后光合能力恢复程度较高，即干旱没有给这两个品种造成严重的光破坏，而两个品种之间，葡萄园皇后在重度干旱胁迫下的φPSⅡ明显低于赤霞珠，说明其光合器官在严重干旱胁迫时对光能的利用率较差；新品种皇家秋天和东方品种群的里扎马特在中度干旱胁迫下仍可维持较高的Fv／Fm和φPSⅡ，但在重度干旱胁迫下则降低幅度较大，说明其抵御极端干旱胁迫的能力较差；欧美杂种红双味的Fv／Fm和φPSⅡ随着干旱胁迫程度的增加呈现平缓的下降趋势，而且其φPSⅡ在重度干旱胁迫下是七个品种中最高的，这应该与其此时仍维持较强的光呼吸活性有关；红地球和砧木1103Paulsen的Fv／Fm和φPSⅡ在轻度干旱胁迫下就明显下降，表明干旱条件下其抵御光抑制的能力较差。

It is found that in certain water ratio and consolidation pressure, the values of initial elastic modulus and principal deviator stress increase with intermediate principal stress increasing; in certain intermediate principal stress, the values of initial elastic modulus and principal deviator stress increase with water ratio falling.

试验结果表明：在一定的含水率和固结压力下，偏差应力和初始切线模量均随中主应力比b的增大而增大；在中主应力比b确定的情况下，偏差应力和强度最大值随着含水率的增大而减小。

In Late Jurassic period (159-135Ma), when the orientation of maximum principal compressive stress was NW direction, the Wuzhangshan granite intruded to upward, accompanied the formation of NW trending Sanrenchang and Huangshuian breccia pipe belts; In the Early Cretaceous period (135-120Ma), when the orientation of maximum principal compressive stress was NNW trending, the second stage of Huashan granite intruded to upward, accompanied the formation of NW trending Qiyugou breccia pipe belts; In 120-105 Ma, when the orientation of maximum principal compressive stress changed to NE direction, the gold-bearing quartz veins and gold orebodies in breccia pipes were formed along the NE trending fractures; In the Middle Cretaceous period (105-85 Ma), when the orientation of maximum principal compressive stress was NEE, the NEE trending Leimengou granite porphyry intruded to upward, accompanied the formation of NEE trending Leimengou breccia pipe belts.

在晚侏罗世(159～135Ma)，构造应力场最大压应力方向为NW向，形成了NW走向的五丈山岩体以及NW向展布三人场、黄水庵两个角砾岩带；在白垩纪早期(135～120Ma)，最大压应力为NNW向，形成了花山岩体第二期上侵，并伴有NW向的祁雨沟角砾岩带；其后(120～100Ma)，构造应力场最大压应力方向变为NE向，形成了NE向含金石英脉及角砾岩体中金矿体；最后(100～80Ma)，形成了雷门沟花岗斑岩以及NEE向展布的雷门沟-杨河沟角砾岩带(区域构造应力场的最大主压应力方向为NEE向)。

The production moved off-Broadway to New York City, where she won the Joseph E. Calloway award for her performance, and was profiled in American Theater Magazine as one of ten young theater artists to watch.

生产提出过百老汇的新的纽约市，在那里她赢得了约瑟夫calloway奖，她的表现，并于异型在美国的战区杂志之一， 10战区的青年艺术家观赏。

It's a risk tradeoff, and I believe that adding test support code usually wins.

这是一个风险的权衡，我相信添加测试代码通常会占上风。