查询词典 principal adele

Proximal structures to the overthrust belt evidence compressional folding and faulting indicative ofahorizontal maximum principal stress, but the dominant principal stress of the more distal and productive structures is vertical.

近端结构的推覆带的证据和断层挤压折叠指示ofahorizontal最大主应力，但占主导地位的主应力较远端和生产结构的垂直。

The principal problems concerning pecuniary penalty were:problem of establishing pecuniary penang as a principal penalty,the problem of units and grades of the pecuniary penalty.the problem of bartering pecuniary penalty for remission of terms of imprisonment,the problem of too light or too heavy an imposition of the pecuniary penalty,and the problem of the relationship between the pecuniary penalty and damages.

从1908年到1910年，中央各部院堂官、地方各省督抚、将军都统陆续上奏对大清刑律草案的签注意见，其中涉及罚金的主要问题有：罚金定为主刑问题、罚金单位和等级问题、罚金易刑问题、罚金适用的过轻与过重问题、罚金与赔偿金的关系问题。

Phot oelastic experiment is an effective method which may directly observe and measur e the stress state in the body under the action of outside force in the laborato ry condition, so that it is a fact to gain quantitatively the orientation of max imum principal stress, the trajectories of principal stresses and the magnitude map of the stresses.

光弹物理模拟实验是在实验室条件下直接观察和测量在外力作用下物体内部应力状态和特征的有效手段，能够得到定量化的最大主应力方向、主应力轨迹线和应力级值分布图。

Accountant analyzing accountability from its content and reason, with major point—two kinds of division to accountability: two divided methods and three divided methods; economists analyze the relationship between principal and agency from internal contradiction and its solution. This paper considers that the subject of MA is managerial responsibility from the combination of all kinds'analysis to the accountability and economists' analysis to relationship between principal and agency.

3管理责任的内容是管理结果及其实现过程：管理的本质是资源配置，企业管理分为整管理、系统管理和岗位管理三个层次；管理责任是以最优化的方式实现所要求的结果；管理结果是管理主体所要达到的最终状态，管理过程是达到这一过程的程序和方法，管理结果和管理过程都分为整体管理系统管理和岗位管理这三个层次。

It first choose a mask with a suitable size in the edge image, the local PCA is performed to obtain the principal direction of the mask. The chosen polar angle in Hough transform is limited in a small range emphasizing particularly on the statistical disciplinarian of all principal directions, so it speed up the search time by reducing the range of .

首先在边缘图像范围中选取合适大小的掩膜，通过局部PCA获得支持集内像素点的主元方向；侧重依据所有掩膜内主元方向信息的统计规律来约束Hough变换的极角选择范围，通过缩小参数选择范围大大缩短搜索时间。

Thirdly, the principal curve and polygonal line algorithm are introduced, and an implementation of polygonal line algorithm based on Quasi-Newton numerical optimization is illustrated. The simulation results show that when this algorithm isused in the detection of curvilinear defects on wafer map, it can converge fast, compute accurately and meet the demand of application of defects pattern analysis, and with the number of line segment increasing, the polygonal line will approximate to the Kegl principal curve.

研究了主曲线、多边形线算法，提出用多边形算法识别弧状缺陷想法，讨论了用拟牛顿法实现该算法的解决方案，针对硅片缺点模式分析中常出现的弧状缺陷，采用该算法进行检测分析，实验结果表明这种算法快速准确，当线段个数或最小距离平方期望值达到一定门限值后，多边形线就已经能够描述弧状缺点集的形状，随着线段个数增加，最小距离平方期望值还在不断下降，最终会收敛到Kegl主曲线。

Two series of drained tests with fixed principal stress axes and cyclic rotation of principal stress axes were conducted with a hollow cylinder apparatus at Hong Kong University of Science and Technology.

采用香港科技大学的空心圆柱扭剪仪进行了应力主轴固定单调剪切和应力主轴循环旋转两种不同路径的排水试验。

A new cyclic constitutive model for sands which can describe the deformation behavior of sands under combined variation of principal stress axes and magnitudes was developed based on the above physical fundamentals. And its effectiveness under the complex stress paths including cyclic rotation of principal stress axes is verified by a good comparison of model simulation with test results for sands.

2基于对应力主轴循环旋转条件下砂土的基本变形规律的认识，吸收和借鉴已有弹塑性本构模型研究成果中的合理概念和建模方法，建立了一个可合理描述应力主轴循环旋转效应及主应力幅值大小与应力主轴方向循环耦变效应的砂土弹塑性本构模型，并对该模型在包含应力主轴旋转的复杂循环应力路径下的有效性进行了验证。

The first one analyzed composing and working principal about low speed control system of principal axis.

第一部分，对主轴低速控制系统的构成及工作原理进行分析。

In this paper, in view of the working condition of common principal axes and the exothermic situation, the uneven and steady temperature field of the principal axis system during the working process is described.

主轴是机床或仪器等精密机械的核心构件，它也是影响精度的主要因素，主轴系统的热变形对机械的工作精度影响也很大。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？