查询词典 pressure accumulator

The steam chest ,vapor separators,preheater and surface condenser are designed and constructed for an internal pressure of 1 bar gauge and full vacuum at 121 ℃ except as follows .the shellside of the first effect chest is designed for an internal pressure of 2 bar gauge and full vacuum at 135℃.the bubeside of the prehearter and surface condenser are designed for an internal pressure of 7 bar gauge and full vacuum at 121℃.the equipment is designed and constructed in accordance with asme.certificates are provided.

蒸发分离室，蒸汽室，预热和冷凝器要设计结构内部能够承压1 bar 和在121 ℃充满真空。一效蒸汽室壳侧要设计成能够承压2 bar 和在135 ℃。预热器的管侧和表面冷凝器设计成7 bar 和在121 ℃。设备的设计和制造要符合ASME。要提供证明。

Because of its structure is more simple and less to maintain, in some unimportant or primary pressure control system has been adopted, for example, the steam partial pressure of cylinder pressure control.

由于其结构更简单，维护量少，在一些不重要或初级的压力控制系统中被采用例如，蒸汽分压缸的压力控制等。

When the internal pressure of liquid, which dropped below the liquid at that temperature the saturation vapor pressure at the local area or the formation of steam bubble point; and stress at elevated places around the bubble suddenly breaking pressure, flow due to inertia to high speed to the center of bubble extrusion, hydraulic shock caused by the equipment.

当液体内部压力下降，低于液体在该温度下的饱和蒸汽压时，在局部区域形成汽泡或汽穴；而在压力升高的地方汽泡突然被四周的压力压破，液流因惯性以极高的速度向汽泡的中心挤压，对设备造成水力冲击。

The article covers the full research on such aspects as mathematic description, numerical analysis method and their practical applications. The diphase heating surface is divided into a hot water section, a evaporation section and a micro overheat section , the problems of model switching are avoided successfully between subcritical and supercritical working condition in the model of The diphase heating surface, and the model can be used for between subcritical and supercritical working condition without causing the model stiff infinity prick up problem. The mathematical model and dynamic characteristic account is unified and predigested for the diphase heating surface of once—through boiler under subcritical and supercritical pressure, and propose that the working conditions at phase change point could be used as divide criterion between water region and steam region under supercritical pressure, the problems are solved successfully between water and steam phase change point under supercritical pressure.

本文在过程的数学描述、数值分析以及实际应用等方面进行了系统的研究分析，将双相受热面统一划分为热水段、蒸发段和微过热段三段，所建立的双相受热面模型不但成功地避免了超临界工况与亚临界工况间的模型切换，而且消除了由区段划分欠妥所引起的模型刚性无限加剧的问题，统一并简化了超临界及亚临界压力下直流锅炉双相区段的数学模型和动态特性计算，而且提出了利用相变点工况作为超临界压力下划分汽水区域的标准，解决了超临界压力下水与蒸汽的相变点问题。

This design uses pressure vessel's convention design method, rests on present GB150-1998 "Steeliness Pressure vessel" JB4710-2005 "Steeliness Tower system Vessel" the standard and "Pressure vessel Safety work Supervision Regulations" and so on technical laws and regulations carries on.

本次设计采用压力容器的常规设计方法，依据现行的GB150-1998《钢制压力容器》JB4710-2005《钢制塔式容器》标准和《压力容器安全技术监察规程》等技术法规进行。

Pressure control, pressure warning and fluid position instructionswitch The pressure control switch is independent to the ABScomputer works, is monitoring under the energy storer the cavitypressure.

压力控制开关独立于ABS电脑而工作，监视着储能器下腔的压力。

The paper carried out combination calculation on two kinds unsteady flow problems of pressure water diversion of hydropower station (i.e. pressure fluctuation of water hammer and mass fluctuation of surge chamber), which changed many analytical error caused by considered these two phenomena separately, and such result meets the inherent rule of pressure water diversion system transient of hydropower station much more than before.

2实现了水电站有压引水系统中两种非恒定流问题(即水锤的压力波动和调压室的质量波动)的联合计算，改变了把这两种现象分开单独考虑所带来的分析误差，这样的计算结果更加符合水电站有压引水系统中过渡过程的内在规律。

The swing car bridge with hydraulic pressure pendant is conected with hydraulic pressure assistant loop.,among which can get equal load.The heavy module use hydraulic pressure turning with two cycle loop.

带液压轴悬架的摆动车桥是与液压辅助回路（3点或4点支承）互联的，在这些辅助回路中可得到相等的轴向载荷。

The results show that the tangential stress distribution is decided by pressure gradient, that is, the maximum tensile stress locates where maximum pressure gradient is, while the compressive stress locates where pressure gradients change their direction.

结果显示，轴瓦周向应力分布取决于油膜压力的梯度，最大拉应力位于压力梯度最大处，而周向压应力的峰值则位于压力梯度方向改变处。

And within the help of ANSYS software, how housing thickness, plastic module of housing and oil film pressure gradient effects the bearing stress distribution is analyzed in this paper. The relationship between alloy tangential stress or radial stress or shear stress and oil film pressure or pressure gradient is also analyzed.

利用ANSYS软件分析了轴承座厚度、轴承座弹性模量和油膜压力梯度对轴瓦应力分布的影响，分析了轴瓦合金层周向应力、径向应力和剪应力的应力场与油膜压力及油膜压力梯度的关系。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。