查询词典 pressed

I coated the outside of the bearings with epoxy and pressed them in with an arbor press(a vice, or hammer should work fine too), as deep as possible so that I could still tighten the set screws.

余涂层的外部轴承环氧树脂和压制他们的安娜堡新闻（副主席，或锤应该也没关系），深使我仍然可以加强紧定螺钉。

However disc refining was working continuously with high concentration and asbestos fiber was defibered well, since it was pressed and twisted effectively.

使石棉纤维松解分丝，尤其是当磨浆转数为1400r时。石棉纤维松解分丝良好，且纤维切断很少。其石棉胶乳抄取板的抗张强度达到最大值。

If the packing pressed tight, the wear between axle sleeve and packing will beincreased.

因为是从水泵的压水室引水，这样到达填料密封腔的轴封水的压力过高，从而造成填料处轴封水泄漏量过大。

I turned back and pressed the shutter

最后我还是忍不住折回去给他拍个照

Sustainability is not only reflected in the energetic concept of the design but also in, plan and materials including untreated wood with FSC-label and grasses as reed and pressed bamboo.

可持续发展的理念不仅仅体现在充满活力的设计理念上，而且体现在材料上，包括未经加工处理的木材，芦苇草以及竹子。

Re-call Key: after the bank assistant pressed the " Call" key, but this customer did not come to the window, the assistant can press this key to call this customer for many times.

&重呼&按钮：营业员按&呼叫&按钮后，该受理号码的客户没来窗口办理业务时，可按此按钮对该客户多次呼叫。

It fires from an open bolt (the barrel also is held back when gun is cocked, and it is released only when the trigger is pressed).

它从一个开放的火灾螺栓（桶也被压住枪竖起时，它才释放触发器时，按下）。

Contact damage analysis of composite beam and composite plate pressed by static loading are accomplished in the third part.

三、对复合材料层合梁和复合材料层合板受静载时的接触损伤问题进行了分析。

During the winding of magnetic pole coils used in synchronous electric motors, cold hardening is induced by press bending at 90°, by which the coils are hard to be pressed and shaped, thus local resistivity increases and results in influence on the coil lifetime.

摘要同步电动机磁极线圈在编绕加工时，90℃角处因压弯而产生的冷作硬化现象使线圈无法装压成型，且局部电阻率增大，甚至影响磁极线圈使用寿命。

The procedure of biscuit firing of clad plate base blank is carried out as follows: Weigh a certain amount of raw material in proportion by feeder, by conveyor belt the raw material is ground in a ball mill; after grinding for 12 hours, sifting-out and de-ironing, it is transferred to be homogenized and outworn in homogenization pool; then after spray drying granulation in spray tower, the powder is pressed into a certain size of blank by brick machine, afterwards, the blank will be dehydrated in drying kiln, through high-temperature sintering, base blank of clad plate with stable mechanical, chemical, physical performance has been finished.

复合板地柸素烧由以下环节组成：用喂料机按比例称取原料配料，通过传送带将原料传送到球磨机内球磨，球磨12小时后过筛、除铁，然后转移到均化浆池进行均化、陈腐、随后通过喷雾塔干燥造粒，将得到的粉料通过压砖机压制成所需规格的生柸，生柸在干燥窑干燥，随后在窑炉中高温烧制，得到具有稳定机械、物理化学性能的复合板底柸。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。