查询词典 preheater

It consists of substrates preheater, intelligent proportion-integral-derivation controller and computer serial collecting and feedback control components.

该系统由基板预热器、智能比例微分积分控制器以及计算机串口温度采集反馈控制等3部分组成。

Especially, because of curve structure in front of heat pipe air preheater, there is more # c3 z: k Y6 k

然而，在锅炉上的实验肯定要花费很大的人力、物力和时间。

Rotating Air Preheater was produced in China in 1980's via the technology introduced from the America CE Corp.

回转式空气预热器是我国八十年代由美国CE公司引进技术制造的，是电站锅炉的重要辅机之一，它起着利用热能的热交换作用。

Second, the flow behavior of preheater cyclone has been analyzed.

分析了预热器旋风筒内部气流场的流动特性，包括其内部速度、湍流结构及压强分布的特性，以及气相颗粒在流场中的运动行为。

However, there lies a particular air leakage problem of revolving type air preheater, which will lead to serious energy waste.

但是容克式空气预热器有一个独特的漏风问题，空预器漏风会引起严重的能源浪费。

On the other hand, this kind of method need the emendation of specific air preheater which depresses the generality of the hot spots detection system.

另一方面，直接采用红外传感器进行温度检测的方法需要对具体空预器的发射率进行校正，减小了系统的通用性。

The technical core and performance feature of inorganic heat tube,and its application on air preheater of atmospheric furnace were recommended briefly.

简要介绍了无机热管技术的核心和性能特点以及在常压炉空气预热器上的应用情况。

Basis on the result of research, there were come to some conclusions: First, in order to get the more ideal results, we must adopt Reynolds Stress Model based on anisotropy, QUICK format and PRESTO format on the premise of good mesh for the simulation of the complex flow field in preheater cyclone.

基于模拟研究结果，得到了相应的一些主要结论：①模拟必须采用基于各向异性的RSM湍流模型，同时还要相应的采用二阶迎风格式和PRESTO压力插补格式，才能获得较理想的模拟结果。

The steam chest ,vapor separators,preheater and surface condenser are designed and constructed for an internal pressure of 1 bar gauge and full vacuum at 121 ℃ except as follows .the shellside of the first effect chest is designed for an internal pressure of 2 bar gauge and full vacuum at 135℃.the bubeside of the prehearter and surface condenser are designed for an internal pressure of 7 bar gauge and full vacuum at 121℃.the equipment is designed and constructed in accordance with asme.certificates are provided.

蒸发分离室，蒸汽室，预热和冷凝器要设计结构内部能够承压1 bar 和在121 ℃充满真空。一效蒸汽室壳侧要设计成能够承压2 bar 和在135 ℃。预热器的管侧和表面冷凝器设计成7 bar 和在121 ℃。设备的设计和制造要符合ASME。要提供证明。

At present, thermocouple or infrared thermometer are usually used as temperature measurement instrument in most air preheater hot spots detection systems.

这些沉积物很容易发生自燃，称为空预器的二次燃烧，需要对空预器进行热点检测来加以预防。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。