查询词典 powder process

An improved mathematical model was established to describe the mechanical behavior of Fe powder compacting process.

针对铁粉材料，建立了一种新的数学模型，用于描述压制过程力学性能变化。

A process for decomposing CO2 generated industrially includes such steps as collecting CO2 tail gas, dusing and desulfurizing, oxidizing degradation in oxidizing tower, decomposing the oxidized tail gas in reactor to obtain oxygen gas for exhausting it and carbon-contained gas, and preparing carbon powder in carbon absorption tower with electric decarbonizing unit.

一种工业产生二氧化碳的分解处理方法，它包括：对二氧化碳尾气进行收集；对收集的尾气进行除尘和脱硫处理；将处理后的尾气送入氧化塔做二次氧化降解处理；将二次氧化的尾气送入反应槽进行分解；将分解后的氧排出，分解后的碳气送入一个碳吸塔的电除碳器形成碳粉。

Using modified conventional powder metallurgy process for sintered Nd-Fe-B magnets , including annealing of ingot alloy, hydrogen decrepitating, modified jet mill and adding additive during jet milling, we have mass-produced high performance and high corrosion resistance sintered Nd-Fe-B magnets from a conventional ingot alloy without strict protections against oxidation.

利用改进的传统粉末冶金工艺(铸锭热处理、氢爆、改进型气流磨设备以及在气流磨中掺入添加剂等)，在无严格的防氧保护情况下，从传统合金铸锭出发，工业化生产出具有高耐蚀性的N48～50档烧结Nd-Fe-B 磁体。

It is shown that uniform powder cloth with proper thickness can be produced by using appropriate rolling parameters. Thermogravimetic and pyrolysis residuum analysis indicate that the burnout process of fugitive binder used to produce the cloth is found to take place in two stages, no residuum is left when degassed properly.

结果表明，采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布；热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段，合理除气后，基本没有残余物。

The results show that MgO powder is enwrapped by the BST sol during the Sol-Gel process.

结果表明，采用溶胶－凝胶法制备出包裹MgO粉体的BST凝胶，凝胶经干燥、预烧得到BST/MgO复合粉体。

This method can control the process of jelling and obtain the SnO2 powder gas sensitive with uniform distribution and pretty dispersibility. These materials are featured by excellent repeatability and consistency, low-cost.

探索了双氧水和半透膜结合的新的无机盐溶胶-凝胶工艺方法制备纳米SnO_2气敏材料，该工艺方法可以控制胶凝过程，得到化学成分分布均匀，分散性好的SnO_2基气敏粉体材料，具有重复性强，一致性好、成本低廉的特点。

This research is a new low cost method of producing abrasive grit. It is to put the iron ore concentrate, coal powder, hydrated limed and addition agent together to make coal mixed pellet in prior which is rapidly auto-reduced in high temperature and kept about 10min above 1350℃, and then furnace cooled. The 2CaO·SiO2 of slag phase change、volume increase and natural bloom in reduction process. Finally we obtain no-slag abrasive grit through screen separation , in which the iron yield can be above 90%,the sulfur content can be below 0.05% and carbon content is lower than 4.0%.

本研究是一种全新的低成本生产铁粒的方法，它是将铁精粉、煤粉、消石灰和添加剂预先制成球团，在高温下迅速加热还原，在1350℃以上保温10分钟后随炉冷却，渣相中2CaO·SiO2在冷却过程中发生相变，体积膨胀而自然粉化，通过筛分便可以得到不含炉渣的铁颗粒，铁的收得率在90%以上、S≤0.05%、C在4.0%左右。

The weight percentage for the components of the hyaline coating is as follows: SiO2 45 to 54 percent, B2O3 15 to 20 percent, one or more of Na2O, K2O and Li2O, 10 to 24 percent, one or more of TiO2, ZrO2 and ZnO, 6 to 18 percent , and the rest is one or more of CaO, MgO and CeO2. Firstly, the glass powder is mixed with the mill additions to be pulped and then plated on the surface of titanium or the titanium alloy. After being dried, the surface of titanium or the titanium alloy is directly used for a thermal hydrogen treatment or smelted at a temperature of 900 to 1, 000 DEG C for 15 to 30 minutes and then a hyaline coating with a thickness of 20 to 70 micrometers is formed on the surface of titanium or the titanium alloy; secondly, titanium or the titanium alloy plated with the coating is conducted a thermal hydrogen treatment. After the treatment technique is finished, the coating flakes off automatically in the process of cooling; and finally, a surface treatment is supplemented to meet the requirement of the workpiece surface.

该玻璃质涂层成分按重量百分比：45-54SiO2，15-20B2O3，10-24Na2O、K2O、Li2O中的一种或多种，6-18TiO2、ZrO2、ZnO中的一种或多种，余量CaO、MgO、CeO2一种或多种，将玻璃粉与磨加物混合制浆并涂覆在钛或钛合金表面，干燥后直接用于热氢处理，或在900-1000℃下熔烧15-30min，在钛或钛合金表面制得20-70微米玻璃质涂层，随后将制有该涂层的钛或钛合金置于氢气气氛下进行热氢处理，处理工艺结束后，涂层在冷却过程中自剥落，最后辅以表面处理即可满足工件表面要求。

The present invention adopts ammonium salt solution as leach, and adopts the liquid-phase oxidation activating agent formed from surfactant sodium ligno-sulfonate or sodium dodecyl sulfonate, liquir phase oxidation catalyst Cu(2+) and sulfur-extracting agent tetrachloroethylene to implement quick leaching process of sulkfide mineral in gas-liquid-solid three-phase reactor, all the sulfurs contained sulfide in mineral powder can be converted into elementary sulfur and sulfuric acid radical, the contained zinc, copper, nickel, cobalt, lead, cadmium and silver can be changed into soluble salt, and fed into leach or remained in the leaching out slag.

本发明涉及的有色金属硫化矿的铵盐液相氧化直接浸出方法，其特征在于：采用铵盐溶液作浸出剂，采用由表面活化剂木质磺酸钠或十二烷基磺酸钠，液相氧化催化剂Cu2+、萃硫剂四氯乙烯组成的液相氧化活化剂，在气液固三相反应器内，实现硫化矿的快速浸出过程，矿粉中各种硫化物所含的硫转变为单质硫和硫酸根，所含的锌、铜、镍、钴、铅、镉、银等变成可溶性盐类进入浸出液中或留在浸出渣中，消除传统流程中二氧化硫，硫化氢，氮氧化物及含砷含汞含铅等有毒烟气的排放。

Production process: after casting, extrusion, tinting, electrophoresis, powder coating, fluorine carbon spraying, mould, polishing, wood, metal wiredrawing, such extrusion.

生产工艺：经过熔铸、挤压、氧化着色、电泳、粉末喷涂、氟碳喷涂、模具、抛光、木纹、拉丝、钣金等挤压而成。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。