查询词典 position parameter

The geology research of carbonate reservoirs in Ordovician of Tahe oilfield showed that many large dissolved vugs and fractures were developed. The spread of the reservoir take on a very heterogeneous state. And the typical fractured-vuggy reservoirs was formed. According to the combination of the various spaces, the formation was divided into vuggy formation, fractured-vuggy formation and fractured formation. The research showed that development of the vug is relevant to the its position on the structure, the fractures, the water surface and the weathering surface. Multi-phase charge and recharge of the oil in the reservoirs resulted in the complexity of the fluid distribution. So the"Bottle Model"was brought forward to explain the movement of the water-oil contact. The special storage space and the complex fluid distribution lead to the unstability of the production and the complexity of the water cut. In order to explain the characteristic of the fracture-vug unit was brought forward and the basic principle and method of the partition of the fracture-vug unit was formed. The classification and evaluation of the units were performed according the reserve and energy. Based on the research of geology characteristic and the fluid flow in the reservoir the comprehensive numerical simulation plan of the fractured-vuggy reservoirs were established. Through the selection of the simulation unit, fluid flow type and parameter equivalent the triple media reservoir simulation model was established. Considering the practical application the model was resolved by the DKR decomposition conjugate grads method. Based on the fine reservoir description of Dsitrict IV of the Tahe oilfield the various space type were classified and combined together. The geology model of Unit S48 was constructed. Two typical single well model was established according to the geology and the dynamic phenomena. Finally the single well model and the Unit S48 were simulated by the triple media reservoir simulator. Via the local grid refinement and coarsening in the simulation good matchs were gained. Based on the results of the simulation the reserve distribution, percent of reserve produced in various space and the natural energy were analyzed. The fluid was storaged in the fractures and vugs mostly and more than 90% the produced oil came from the systems. The energy belonged to the active one. The results of simulation accorded with the fact and showed the validity and practicability the research and the simulator.

塔河油田奥陶系碳酸盐岩油藏的地质研究表明，其储层中发育着很多大型的溶蚀洞、缝，储层的平面展布呈现出极度的非均质性，形成了典型的缝洞型碳酸盐岩油藏，根据各种孔隙介质在储层中的组合，将储层分为了溶洞型、裂缝-溶洞型和裂缝型三类；研究表明溶洞储层的发育和构造位置、裂缝的发育、潜水面和风化面的位置等因素有关；多期充注的油气成藏模式导致了流体复杂的赋存状态，由此提出了所谓的&瓶子模型&，解释生产过程中油水界面的变化；特殊的储集空间类型和流体分布特征导致油田在开发过程中表现出很大的不确定性和含水变化的复杂性，为了合理的解释油气田开发过程中的动态特征，提出了&缝洞单元&的概念，并制定了&缝洞单元&纵横向划分的基本原则和依据及划分方法，并对&缝洞单元&进行了分类和评价；基于地质特征和流体在其中流动规律的研究，提出了缝洞型碳酸盐岩油藏的数值模拟综合解决方案，通过模拟单元的选择、流动类型和参数的等效，建立了三重介质油藏三维三相数值模拟模型，采用不完全LU分解预处理共轭梯度法进行了求解；在塔河油田4区精细油藏描述的基础上，将各种类型的孔隙空间进行了归类组合，建立了S48单元的地质模型；通过对油井生产动态进行分析研究，建立了两类和油井地质、生产动态相对应的单井模型；最后应用三重介质油藏数值模拟软件对单井模型和S48单元进行了数值模拟，通过局部加密和粗化等技术模拟流体流动规律，取得了很好的拟合效果；结合数值模拟结果，分析了各种介质中的储量分布、储量产出的百分比以及地层的能量，认为塔河油田缝洞型油藏中流体绝大多数储集于缝洞系统之中，所产出流体90%以上也来自于缝洞系统，其底水能量属于较充足的类型；模拟结果和油田实际情况符合较好，说明了地质研究和油藏数值模拟研究的正确性。

The breakthrough of respect of the innovation of two paces zymotechnics, detached technology, application that ferments the improvement of craft reachs computer technology, make C of our country vitamin produces craft parameter can accuse gender and optimize degree to rise ceaselessly, turn by inferior position in international competition for the advantage, changed the competitive structure of world vitamin C.

两步发酵法的创新、分离技术方面的突破、发酵工艺的改进及计算机技术的应用，使我国维生素C生产工艺参数的可控性和优化程度不断提高，在国际竞争中由劣势转为优势，改变了世界维生素C的竞争格局。

Discrete sliding mode theory has been applied to electrostatic levitation system in which general discrete state space expressions with parameter variation have been set up based on gyro rotor electrostatic force equation and other annuluses including high-voltage amplifier, position sensor and time delay.

本文将离散滑模控制理论应用于静电陀螺悬浮系统，根据陀螺转子静电力方程以及各环节特性(包括高压放大器、测量环节和数字控制器的滞后环节)，建立考虑系统参数变化的广义被控对象离散状态空间表达式。

The average percent value of G C (49.3%) was less than that of A T (50.7%), there was a bias of the content of G, T in the third codon; The number of transition G-A and T-C were 22, 15 respectively, which were higher than that of transition A-G and C-T, the number of tranversion C-A, T-G is 2 respectively, and other tranversion patterns didnt occur; the probability of transition was higher than that of tranversion , Ts/Tv = 9.5-19, there was the highest number of transition in the third codon. The gamma parameter a of the lst,nd and 3rd codon positions were 0.00572,0.01237 and 1.05239 respectively, they showed that there was adifferent substitution rate at different codon position. Frequences of synonymous codon usage were relatively biased. The average rates of synonymous and nonsynonymous substitution were 0.0787, 0.0011 respectively, there was a significant difference between dS and dN (Z = 4.713, p.01), and the low ratio( CD = 0.0284 .3) of dN/dS ratio impled that there were selective constraints against the nonsynonymous sites in cyt-b gene, The distribution of nonsynonymous codon substitution pattern related to Grantharm distance indicated that the purified selection at 2nd codon positions was more intensive than that at 1st codon positions. The phylogenetic trees supported the view of the double origin of Chinese goose, which means that domestic Chinese goose was derived from Anser cygnoides and domestic European goose, and Yili was derived from Anser anser.

碱基含量分析可知，序列的G C含量(49.3％)＜A T含量(50.7％)，密码子第三位点的G、T含量都有较强的偏倚性；序列间G→A和T→C的转换数(22次和15次)高于A→G和C→T的转换数(10次和9次)，C→A、T→G颠换数均为2次，其余颠换模式均未发生；转换数明显高于颠换数，Ts／Tv=9.5～19，密码子第三位点的转换数最高，呈现了相当强烈的转换偏倚性；密码子第一、二和三位点的gamma分布参数α值分别为0.00572、0.01237和1.05239，表明密码子第一位点的替换速率变异最大，第二位点次之，第三位点的替换速率变异相对较小；编码同一氨基酸的同义密码子并非随机使用，表现出一定程度的使用偏倚性；同义替换速率和非同义替换速率分别为0.0787和0.0011，dS与dN值间的差异极显著(Z=4.713，p＜0.01)，而ω=0.0284，明显小于0.3，表明雁属鹅细胞色素b基因序列经历了中度净化选择作用；单步非同义替换(Sing-step nonsymonymous codon substitution，SSNCS)分布模式与Grantharm距离之间的关系说明密码子的三个位点所受的净化选择强度不同；构建的最大简约树与邻接树拓扑结构一致，支持中国家鹅的双起源学说，即除伊犁鹅外的其它中国鹅品种起源于鸿雁，伊犁鹅和欧洲的郎德鹅、莱茵鹅起源于灰雁。

A multi-distance measurements method is employed in this paper. A single parameter fitting method and a double parameters (reduced scattering coefficient and amplitude factor) fitting method on the basis of the least square Newton fitting algorithm is used to derive the optical parameters respectively. For the finite-thickness homogenous tissue, it can be concluded that the rest terms in expressions of diffusion reflectance and transmittance for the corresponding tissue geometries that subtract the exponential term contained source-detector distance depend on the detected position weakly.

在多程测量的基础上，使用单参数最小二乘牛顿法拟合方法和双参数（约化散射系数、幅度因子）最小二乘牛顿法拟合方法，得到有限厚均匀组织的反射率分布和透射率分布公式中除去包含测量位置的指数项的其它部分对测量位置皆具有弱依赖性的结论，并对拟合结果进行了分析讨论；而对于有限厚平板状双层组织，可根据对反射测量结果及透射测量结果进行拟合所得的约化散射系数间的差异及常数因子的正负判断双层组织的可能结构分布。

The location compute equipment of object is an effective means to acquire object's location quickly and accurately, target distance parameter is offered by laser range finder, and geodetic position of observation point is obtained by GPS, azimuth and pitch angle are offered by azimuth compass.

目标位置解算装置是快速、准确地获取空中或地面目标位置坐标的有效手段，由激光测距机提供目标距离参数，由GPS接收机获得观测点坐标参数，方位获取设备提供目标方位角及高低角参数。

Stability analysis of nonlinear magnetic suspension, the magnetic suspension system model was found based on electromagnet dynamics and voltage balance of the electromagnet coil; The feedback of position and velocity and current are used as the control variable; After the control rule was applied to the electromagnetic system, the louts criterion was used to get the range of the control parameter in which the system was steady-going.

非线性磁悬浮系统的稳定性分析，通过电磁铁动力学和电磁线圈的电压平衡方程，建立磁悬浮系统基本模型。求出系统奇点后，通过系统线性展开求出系统矩阵。用PD控制外加电流反馈量，将控制规律带入系统模型方程组求出矩阵的特征方程，由劳斯判据得知非线性系统稳定的位置反馈系数及取值范围。

In the paper, the common expression of the non-uniform load shareing factor was deduced, and a function parameter--forc-arm factor and the concept of ideal centre position were presented and their solutions were given, which makes it possible that the dimensions and the capability of load equilibrium of the mechanism could be determined. The criteria of optimum load balancing mechanisms selection were set up with consideration of the effects of frictions and turning pair clearances.

本文通过对平面连杆式均载机构的功能指标—载荷不均匀系数的推导和分析，提出了力臂系数、理想中心位置这样一些能反映均载机构功能与运动结构关系的参数与概念，并给出其求解方法，它们还可以用来确定平面连杆式均载机构各构件的最佳长度尺寸。

The present paper elaborated a fluid position —current capacity cascade control system design method and the step, introduced its parameter set method.

本论文论述了一个液位——流量串级控制系统的设计方法和步骤，介绍了它的参数整定方法。

When an order is form in position machine, the needed breeds and quantity of cigarette will be established and thesequence and time of cigarette sorting in an order will be also established, so before sorting an order, the order'length can be compute, but before sorting an order, the order's space is existenced as a virtual space, thus supposed a virtual space which loaded finished cigarette and order when virtual space arrive the corresponding sorter, plc control the time parameter and activated the sorting, and the sorter sorting cigarette to virtual space, an order accomplished.

对件烟行走时间进行了建模并提出了一种烟草自动分拣算法，当订单在上位机生成后，所需烟品种及数量随之确定，因此订单中所要分拣的烟分拣的次序及分拣的时刻也就可以确定，所以在订单分拣之前，订单的长度是可以计算出来的，而在未真正分拣之前，订单的长度是一个&虚拟存在的空间&，应用逆向推理的过程可假设一个装成品烟和订单的&虚拟空间&，当&虚拟空间&到达对应的分拣机位置时，通过plc对订单中件烟时间参数的控制，分拣机自动分拣件烟至&虚拟空间&完成订单分拣，该算法实现方便并能节约大量的硬件成本，对其他一些物流分拣行业也具有一定的推广价值。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。