查询词典 position parameter

In this study, the problem to estimate physical parameter distribution, load property and load position were investigated.

论文研究了如何由测量数据估计振动系统的物理参数分布、负载特性与位置估计问题，对于声学设计与检测有一定应用价值。

The effects of drawbar length, articulation joint position on path following performance are investigated using parameter analysis method.

采用模型参数化分析方法，讨论了牵引杆长度、主车与拖车和拖车与拖车的铰接点位置对主车与拖车轨迹同辙性的影响。

This paper uses the ADAMS software to set up a dynamic model of tractor-trailer combination consisting of one tractor and five trailers with a total of 13DOF. The effects of drawbar length, articulation joint position on path following performance are investigated using parameter analysis method.

本文应用机械系统分析软件ADAMS建立了由一节牵引车和五节双轴转向拖车组成的汽车列车系统13个自由度的动力学模型，采用模型参数化分析方法，讨论了牵引杆长度、主车与拖车和拖车与拖车的铰接点位置对主车与拖车轨迹同辙性的影响。

This thesis proposes another approach, which makes the phase current be inphase with each phase back-EMF respectively by tuning a parameter in the new sensorless algorithm at the steady state to intentionally produce rotor position estimation error.

此外，为了提升稳态时马达的运转效率，本论文提出一个参数调整机制，刻意的使估测结果产生误差，使各相电流能与反抗电动势同相。

So the main study contents of this thesis are as follows: the load distribution pattern along the length beam and the cross beam in the place of node、 the appropriate matching rigidity of the length and cross beams in the action of same anchorage force and the affection pattern discuss on sloping surfaces dip angle、 beam rigidity 、 anchor-rope angle as well as the position of load which affect the load distribution ratio on length and cross beams. In the end it brings forward lattice beam internal force calculated method on the basis of double parameter groundsill model.

鉴于此，本文主要的研究内容是格构梁节点处荷载沿纵横梁的分配规律、同一锚固力作用下纵横梁合理的匹配刚度以及对格构梁纵横梁荷载分配比值可能存在影响的坡面倾角、梁刚度、锚索夹角、加载位置等因素的影响规律探讨，最后提出基于双参数地基模型的格构梁内力计算方法。

Firstly,to abtain the parameters of coupling system,such as the focal length and the position of the lens,computing the Gaussian lens formula,then establishing the rectangular coordinate system and constructing equation and tracing the marginal ray to compute the parameter of the radius of the image beam waist.

首先使用高斯光束的透镜变换公式计算透镜的焦距及放置位置等耦合系统的参数，然后建立直角坐标系并利用耦合系统的参数构建方程，对边缘光线追迹，计算出像方束腰半径值。

To weaken the influences of the position-dependent periodic disturbances and parameter uncertainties, the robust repetitive controller was designed, which associated structure singular value theory with the discrete-time repetitive control theory. The problem of robust repetitive control was transformed into one of H∞ optimal control using linear fractional transformation. The robust repetitive controller was achieved using D-K iteration procedure and made the servo system have stability, robustness and tracking performance.

为了削弱周期性扰动及参数变化不确定性的影响，将重复控制和结构奇异值理论相结合，利用线性分式变换(linear fractional transformation，LFT)将鲁棒重复控制问题转换成H∞最优控制问题，采用D-K迭代法设计鲁棒重复控制器(robust repetitive controller，RRC)，实现系统的稳定性和鲁棒性，提高系统的跟踪特性。

The power spectrum density and mean square value of acceleration at every output position including the driver's seat are computed by means of solving the frequency response function, so as to show the changes of vibration magnitude through parameter-transformation.

在计算中除考虑了多点输入的自谱及前后轮之间的互谱外，还根据有关路面资料考虑了左右轮之间的互谱。结合乘坐舒适性研究，绘出了座椅振动量随各参数变化的一些规律，可为今后设计工作参考。

Markov proved the minimality of variance of LSE in 1900. this is the famous Gauss-Markov definition, which found the position for LSE in parameter estimate field.

后来， A。 A.Markov于1900 年证明了LSE 的方差最小性质，即著名的Gauss -Markov定理，奠定了LSE 在参数估计理论中的地位。

Servo controller is key part of antenna control system.In some servo controller,classic PID control algorithm is adopted. In order to improve precision of control system,the integral parameter has been turned too big to use because it will cause integral saturation which depress system performance.On the other hand,ISA bus is used to communicate between servo controller and main computer.ISA is low speed interface protocol,it cannot provide more data for complicated real time position control in servo controller.

伺服控制器是天线伺服控制系统的核心环节，经典的PID控制算法在整定时整定出的积分环节参数较大，很容易出现积分饱和，造成控制精度的降低；另一方面伺服系统中伺服控制器与主控计算机通过低速的ISA总线进行通信，无法满足控制器进行复杂的位置控制运算所要求的实时大信息量的数据传输。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。