查询词典 porous

It is shown that the porous particles are less energyconsuming to fluidize and, with their contents varying from 5%～25% in the riser, the minimum fluidization velocities based on gas stream are from 0.87×10-3 m/s to 2.2×10-3 m/s, while the critical transport velocities are from 1.0×10-2 m/s to 1.6×10-2 m/s for the operation with no liquid circulation or from 5.2×10-3 m/s to 7.1×10-3 m/s for the condition with liquid circulation.

例如，流化床电极、造粒、砂滤、结晶、浮选、聚合、煤气化、费-托合成[1]等。废水处理中三相流化床的应用得益于生物工程中的生物膜法和化工操作中的流态化技术的成功结合，主要优点为宏观混合程度高，固相内扩散阻力低，液体和固体外部传质阻力小，微生物浓度高。

A porous media model is introduced for a description of foam silicone rubber .

泡沫硅橡胶是一种典型的多孔材料，同时它的本构行为也呈现超弹性力学性质。

The results show that the optimal amount of foamer is 0.5 wt％and thisporous material has excellent porous structure, that is, interconnected and uniformlydistributed pores with the diameter of pores ranging from about 100μm to 700μm.

结果发现：发泡剂的最佳比例为0.5 wt％，多孔n-HA／PA6材料具有与松质骨相似的多孔结构，孔径为100～700μm，孔的贯通性好，孔隙率可通过调节工艺参数进行控制，最高可达到88.6％；总孔隙率相近的情况下，n-HA含量高的多孔材料的压缩强度较高；孔隙率在58～88％范围内，多孔材料的抗压强度在1.1～15.6MPa，与人松质骨的抗压强度相当。

The performances of the porous material and the optimal amount of foamer wereinvestigated.

本研究还采用注塑成型方式制备了多孔纳米羟基磷灰石／聚酰胺6(n-HA／PA6)复合材料，考察了发泡剂的用量及多孔材料性能。

Based on the mechanisms of foam flow in porous media, a new parameter of foam comprehensive value was employed to evaluate foamers, which denoted the comprehensive characteristic of foamer's foaming ability and stability.

论文根据氮气泡沫渗流机理，提出将反映起泡剂起泡能力和稳定性的综合性能的泡沫综合值作为主要参数，用于氮气泡沫调驱用起泡剂的筛选。

The porous architecture can be adjusted by the combination of processingparameters such as the weight of starting mixture used per mold and the ratio ofcomposite to foamer as well as n-HA content in n-HA/PA66 composite.

孔隙率和孔隙结构受单模材料用量，发泡剂比例和复合材料中纳米羟基磷灰石含量的影响。

A series of porous metallic matrix with various porosity and good shapes were manufactured through adjusting the partitioning among Ni-Cr filler, high temperature solid grains and foamer by loose powder sintering. The elastic modulus of the matrix was measured.

以松装烧结方法为基础，通过调整Ni-Cr合金钎料、高温固相颗粒和造孔剂的配比，采用合适的烧结工艺，制备出具有不同孔隙率、形貌较好的多孔金属胎体试样，并测量了胎体试样的弹性模量。

It is revealed that a certain amount of excessive formamide is favorable for preparation of the aerogel with high porosity, while more excessive glycol can deteriorate the formation of nano-porous SiO2 aerogel network. Additionally, the pH value of the reaction system has a strong impact on the microstructure and properties of prepared SiO2 aerogel.

研究发现：微过量的甲酰胺，有利于高孔隙率气凝胶的合成；过量的乙二醇的引入不利于低密度气凝胶的形成；pH值对合成气凝胶的性质也有较大的影响。

Also,the relationship,that is Dui=(φ2i)/(m+1),between fractional number m and experimental data in the porous catalyst bed has been obtained.

而且，在多孔固体催化剂颗粒填充床中分数参数m和实验数据间的关系Dui=(φ2i)/(m+1)也已推得。

In order to overcome the difficulty of making a through investigation of each fracture in natural systems, a new concept of quasi double-porosity-medium was put forword and a new mcdel was also developed based on the partition of dominant fractured networks and quasi porous matrixes according to the transmissive and storage mechanism of frae tured medium.

双重介质水流耦合离散模型的建立，改变了以往对双重介质的概化和假设，能如实的反映裂隙系统和孔隙岩块的组合关系，不仅能描述裂隙系统的导水作用和孔隙岩块的贮水作用，还能描述孔隙岩块的渗透特征。对两类空隙系统间的水交替特点有了新的认识，并对以往的结论提出异议。

Now she was hungry and angry.She began to smoulder.

现在她又饿又气，她开始流露难以抑制的怒火。

You have placed our iniquities before You, Our secret sins in the light of Your presence.

诗90：8 你将我们的罪孽摆在你面前、将我们的隐恶摆在你面光之中。