查询词典 plate cylinder

Professional production of badges, Su key chain, ash Cylinder, Opener, the ball cross, wallet, bracelets, rings, earrings, hair clips, necklaces, etching Loukong, medal trophy, the Haopai, doll plate, tyres folder, brooches, nameplate, belts deduction And so on.

专业制作徽章，觫匙扣，烟灰缸，开瓶器，球叉，钱夹，手镯，戒指，耳环，发夹，项链，蚀刻镂空，奖牌奖杯，工号牌，公仔标牌，呔夹，胸针，铭牌，皮带扣等等。

Methods Using ultrasonic technology, flavonoids were extracted form Glycyrrhiza by orthogonal experiment, and their bacteriostatic activity were studied by cylinder plate method.

方法利用超声波技术通过正交试验提取甘草中的黄酮，杯碟法对其进行抗菌活性的研究。

Carbon tissue: A thin paper coated with gelatin , plastic and pigments used to transfer the photographic image from film to a gravure plate or cylinder.

碳素纸：表面涂上明胶，塑料和颜料的薄纸。用来把菲林上的影像转移到凹版版片或圆筒上。

Through the study of different structure forms of the cylinder head, influences of different types of structure schemes of the floor plate, head plate, inlet and exhaust ports as well as of jobbing sheet's different locations on the changing disciplines of overall stress level were achieved.

通过对气缸盖结构型式的研究，得到了典型高速大功率柴油机气缸盖的底板、顶板、进气道、排气道采用不同的结构型式，中隔板处于气缸盖的不同位置时，气缸盖整体应力水平的变化规律。

A correlation of the experimentaldynamic response of the vessels with the theoretical finite element calculations ispresented and discussed.1 The response of the end caps is dominated by transverseand torsional deformation of the plates.The membrane strain is negligible compareto the lateral strain.2 In the lengthwise direction of the inner cylinder,themembrane strain has the same magnitude as that of the bending strain. But for theouter cylinder,the former is much smaller than the later at the same direction.3 Forboth the inner shell and the outer shell,hoop strains are primarily due to themembrane deformation.The amplitude of the circumferential flexural strain isconsiderably small.4 Peak strains in the vicinity of the connection portion of theend caps and the shells are very high.This is important to assess the safety of thecontainer in case of repeated use or tests.5 The applying load to the end cap isdifferent from that to the inner shell plate, but peak stains and nodal displacementsof these two structural parts are nearly the same.It can be inferred that the dynamicresponse of the end cap is greatly affected by the structural vibration excited by theimpulsive loading.

结果表明：1在本文所考虑的载荷水平下，平板变形以板的横向弯曲和扭曲为主，中面应变幅值比较小。2对于内容器，其纵向变形中弯曲应变和中面应变大小接近；而对于外容器，其纵向变形以弯曲为主，中面变形比较小。3内、外壳体的环向变形主要是中面应变，弯曲应变分量很小。4平板和壳体连接处应变很大，这对于多次使用或实验时评价结构安全有指导意义。5尽管内筒底板和大封头上的作用载荷有一定差别，但应变峰值和节点位移峰值基本相近，这说明脉冲载荷激发起来的结构振动对封头的动态响应有很大影响。

The setting plate 2 is provided with a setting hole 2h for aligning the axis of the piston P with the axis of the cylinder sleeve S, and the setting hole is engaged with the knock pin n of a cylinder block B.

该定位板2具有一个允许活塞P的轴线与气缸套S的轴线重合的定位孔2h。定位孔2h与缸体B上的定位销n相配合。

The pressure fields between the cylinder block and the valve plate and between the valve plate and the end housing have been set up, and the HT is designed and checked.

建立了缸体-配流盘，配流盘-后端盖两种配流副之间的压力场数学模型，并据此对液压变压器进行设计和校核，满足最佳配流和强度要求。

In chapter 2, the shortcomings of Innas HT are analyzed. A new structure of the HT is proposed to expand the output pressure scope. The pressure fields between the cylinder block and the valve plate and between the valve plate and the end housing have been set up, and the HT is designed and checked. The computational results meet the requirements of the optimum distribution and strength.

第二章，对Innas液压变压器存在的缺陷进行了分析；为拓展液压变压器的调压范围，提出了一种新型结构，并进行结构设计；建立了缸体-配流盘之间，配流盘与后端盖之间的压力场数学模型，并据此对液压变压器进行设计与校核，计算结果满足最佳配流和强度要求。

In chapter 3, the FLUENT software is used to simulate the 2D and 3D fluid fields of three kinds of distribution pairs (cylinder block and piston, valve port and end cap, valve plate and cylinder block).

第三章，利用Fluent流场仿真软件，对液压变压器三个关键配流副(配流盘-后端盖，配流盘-缸体，缸体-柱塞)的流场进行了初步的二维和三维仿真分析，给出了配流盘控制角度为60°下的仿真结果。

During the plasticizing stage, the melted plastic will not only be pressed dense and solid by the thrust of the screw plate, but also heated by the thermo that transferred from the cylinder shell and by the friction thermo that generated between the plastic particles and the cylinder shell and the screw, with the temperature gradually rising to the melting point.

塑化时，塑料在螺杆罗棱的推动下，在螺槽中被压实，并接受机筒壁所传热量，加上塑料与塑料、塑料与机筒及螺杆表面磨擦生热，温度逐渐升高到熔融温度。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。