查询词典 plane surface
- 与 plane surface 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
In addition, the absolute/convective instability is studied, and the governing region in the parameter plane is declared. It is shown that the absolute instability may become predominant when the electric field or the surface tension is sufficiently large.
另外,研究了单流体射流的绝对和对流不稳定性,在参数平面上给出了它们的控制区域,发现在电场强度足够大或表面张力足够大时,射流可能由对流不稳定状态进入绝对不稳定状态。
-
Using the exterior expression for the Graf′s addition theorem, the closed form solution for scattering of plane SH waves by circular inclusion in half-space is given in the paper. The effect of the inclusion on the surface ground motion is ellustrated and the effect region of the scattering field from the inclusion is analyzed.
文中利用Graf加法公式的内域型表达给出了半空间内含圆形夹塞区出平面散射的封闭级数解答,讨论了夹塞区散射场对附近地表运动的作用,并特别分析了这一作用在地面上的影响范围。
-
Also using the exterior expression for the Graf′s addition theorem, the exact solution for scattering of plane SH waves by circular arc alluvial valley is presented in the paper. From the numerical results the complex effect of the depth-to-width ratio of the alluvial valley on the surface ground motion is found.
利用Graf加法公式的外域型表达,本文还给出了任意圆弧型沉积盆地出平面散射的精确级数解答,提供了大量数值结果并指出了盆地深宽比对地面运动的复杂影响作用。
-
Spontaneously, it can control the output power of quartz light array to achieve the rapid heating control by adjusting the output voltage, and control radiation equilibrium temperature of test piece surface to simulate the aerodynamic heat environment of aerosphere when aerospace plane enters again.
同时,通过调节输入电压的大小,可以控制石英灯阵列的输出功率,实现对快速加热的控制,通过控制试件表面的辐射平衡温度来,模拟空天飞机再入大气层的气动热环境。
-
So it is not easy to turn this idea into reality. We creatively give our parameterization by using the expression of the blending surface in affine coordinate system ([9]) and the plane pencil together.
在仿射坐标系下,二次有轴曲面的表达式相对简单,我们基于厉玉容[9]给出仿射坐标系下拼接曲面的表达形式、不分块直接对混合拼接曲面进行参数化。
-
If the convex surface of a lens is placed in contact with a plane glass plate, as in Fig. 41-9, a thin film of air is formed between the two surfaces.
如果一个凸面镜放置于平面玻璃的一个接触点上,如图41-9所示,在它们两者的表面形成一层空气薄膜。
-
Content: This course discusses the line, plane and quadratic surface in space through algebraic methods, and aims at developing the students' ability to solve geometric problems through analytic methods and to relate geometric intuitive image with algebraic quantitative relation.
主要内容:本课程运用代数方法研究空间解析几何中的直线、平面与二次曲面,培养学生运用解析方法解决几何问题的能力,以及将几何直观形象与代数数量关系相联系的能力。
-
In 1815 he read it to the London Horticultural Society and instructed its members to 'make the surface of your green house roof parallel to the vaulted surface of the heavens, ot to the plane of the sun's orbit'.
在1815年他读到它以伦敦园艺学会,并指示其成员',使表面上你的绿房子的屋顶平行向拱形表面的老天爷,职能治疗,以平面太阳的轨道。
-
The principle that the cylinder drive swing lever to promote scraper plane rotation, so close to the blade surface Dryer (adjusted for normal 1-1.5mm) non-contact dryer, and then to the red balloon gas pressure, air pressure to promote post-marked increase on the blade Pressure, so that the blade surface close to Dryer.
其原理为,气缸推动杠杆摆动带动刮刀架转动,使刮刀靠近烘缸面(一般调为1-1.5mm)不接触烘缸,然后给气囊冲气加压,气囊推动后压标对刀片加压,从而使刮刀紧贴烘缸面。
-
A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t , and punched with compound punching die, and the dimension accuracy reached IT7, the part have a flat surface ,the verticality of tangent plane reached 89.5°, its roughness Ra magnitude are 12.5μm, height of burr are 0.10mm; and the punching part are punched with progressive die, the gap C=7%t , initial accuracy are IT11, and have an more rough surface, even can see the gap with eyes.
例如料厚t=1.5mm的H62黄铜冲裁件,选用C≤40%t单边Ⅰ类小间隙冲裁比选用C≤8%tⅢ类大间隙冲裁,冲件固定误差将加大40%~60%,精度至少降一级。
- 推荐网络例句
-
Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.
在对危险的南部地区访问时,他斥责什叶派民兵领导人对中央集权的挑衅行为。
-
In fact,I've got him on the satellite mobile right now.
实际上 我们已接通卫星可视电话了
-
The enrich the peopling of Deng Xiaoping of century great person thought, it is the main component in system of theory of Deng Xiaoping economy, it is a when our country economy builds basic task important facet.
世纪伟人邓小平的富民思想,是邓小平经济理论体系中的重要组成部分,是我国经济建设根本任务的一个重要方面。