查询词典 pitch-blackness

The coal pitch spheres were produced from the coal pitch by suspension method.

以煤沥青为主要原料采用水浴悬浮法制备沥青球。

Coal tar pitch and petroleum pitch were prepared from petroleum residues and coal tar by air blowing respectively.

分别以煤焦油为原料在300℃空气氧化120min～480min和以石油渣油为原料在220℃空气氧化300 min～720 min，制备了一系列具有相近软化点的煤焦油沥青和石油沥青。

Coal tar pitch and petroleum pitch were prepared from petroleum residues and coal tar by thermal reactions respectively.

分别以煤焦油为原料，在430℃热缩聚50min～270min和以石油渣油为原料在 310℃热缩聚130 min～370 min，制备了一系列具有相近软化点的煤焦油沥青和石油沥青。

In view of domestic coal tar based pitch and actual existing problems,describes the modified pitch process and technique in about ten commercial units which were developed by ACRE,constructed and commissioned in China recently.

根据国内煤焦油沥青产量和存在的现实问题，介绍了由鞍山焦化耐火材料设计研究院开发并投产的近十套工业装置的改质沥青工艺技术。

It was shown from the result that the top line of pitch,pitch range,duration are important cues for stress perception.

研究结果表明，音高高线、调域、音长是表达重音最重要线索，利用这些线索能有效地实现对重音的自动感知。

The word line pitch is about 1.5F, while the digit line pitch is about 3F.

所述字线间距为约1.5F，而所述数字线间距为约3F。

This method could not only applied to outer noncircular gear with all convex pitch line but also applied to outer noncircular gear with partial concave pitch line and inner noncircular gear.

这种磨削原理不仅可以应用于节曲线外凸的非圆齿轮，而且可以应用于磨削带内凹节曲线的外非圆齿轮及内非圆齿轮。

At the same time, the essential motion in the gear grinding process and the structure of gear grinding CNC has been discussed. This method could not only applied to outer noncircular gear with all convex pitch line but also applied to outer noncircular gear with partial concave pitch line and inner noncircular gear.

把成形砂轮看作插齿刀的一个刀齿，就可以利用非圆齿轮插齿加工过程中齿廓成形原理，推导出非圆齿轮齿廓的成形砂轮展成磨削方法，同时讨论了按这一原理磨齿时需要的运动及数控机床结构。

In curve fitting, the speed-flow rate curve shows that the curve of 16mm pitch wheel is a line and that of 12mm pitch wheel is a down-winding curve, the speed-pressure curves of two pitches both are up-winding curves and in the resistance-flow rate curves the curve of 12mm one has lower slope than that of the 16mm one.

曲线拟合结果显示，在转速-流量曲线中，16mm螺距叶轮为一直线，12mm螺距的叶轮为一向下弯曲的曲线；转速-压力曲线显示两者都是向上弯曲的曲线；阻力-流量曲线显示12mm螺距的叶轮斜率较小。

When No. 3 oil is used, put in 3000rpm, 8. 59Nm, the gear surface has an obvious plastic flow, an obvious groove is found on pitch line of the driving gear , an obvious edge is found on pitch line of the driven gear . The operating surfaces of both driving gear and the driven one is high in smooth finish, no pitting. Through the analysis on the gear surface only based on the gear in experiment with No.

实验的结果为：ISOVG68机械油作润滑油时，在输入3000rpm，5.96Nm时，齿面发现沿节线出现大面积的点蚀，且齿面有塑性变形；以3#油为润滑油时，在输入3000rpm，8.59Nm时，齿面发生了明显的齿面塑性流动，主动轮在节线处出现明显的沟槽，从动轮在节线处出现明显的棱脊，大小齿轮工作齿面均十分光洁，未发现点蚀现象发生。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。