查询词典 pipe-rack

If the pipe is not blocked, then the clog could be in the waste pipe, you'll need to check the segment between the trap and the sink for obstruction.

如果没有管道堵塞，那么可以在废管阻塞，您必须检查部分之间的陷阱和下沉阻街。

Heat pipe technique ; waste heat recovery ; heat pipe exchanger ; economical use of energy

热管技术；余热回收；热管换热器；节能

The mechanical expanded joint method is usually used in rehabilitating furnace pipe and big pipe board of waste heat boiler.

废热锅炉是合成氨装置的重要设备之一，其炉管与大管板焊缝受高温高压及介质腐蚀，运行一年后会产生裂纹，影响装置的正常运行。

As the closed process of the change of the working substance states in a heat pipe is the same as the cycle within a thermal power plant, it is very likely that the heat pipe mast be introduced into the heat pump and the therma1 power plant.

由于热管内工质状态变化的封闭过程与工质在热能动力装置循环相一致，所以热管必将扩展应用于热泵和动力装置的广阔领域上。

Making the calculation and analyze of anticorrosion for inner wall of curved pipe and L pipe.

对简单类型的管结点弯管和L型管的内壁腐蚀与防护进行了计算及分析。

Cut out the pipe with pipe facilities. To avoid damaging the sealing ring,thepipe ends must beburred with special burring tool or file completely.

使用切管设备切断管子，为避免刺伤密封圈，请使用专用除毛刺器或锉刀将毛刺完全除净。

It was one term momentous engineering, whereas shallow burring pipe heat preservation ensure water supply normal parameter clause against that at Qing zang railway frozen soil environment carry into execution pipe shallow cover up water supply.

在青藏铁路冻土环境中实施管道浅埋供水是一项重大的工程，而浅埋管道保温则是保证供水正常的首要条件。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工困难的问题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述砬冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进好的了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模与盒形件侧壁小孔翻孔模。

The finite element method was applied to calculate the potential distribution and current distribution on a cathodically protected steel pipe pile. In the calculations, the pipe pile, includion both the submerged and buried sections, was considered as a whole.

把钢管桩作为一个整体，用有限元法计算了几种条件下的电位分布和电流分布情况，讨论了水的电阻率、表面涂层、阳极与钢管桩的距离以及阳极长度等因素对电位分布的影响。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷