英语人>网络例句>pin hole 相关的网络例句
pin hole相关的网络例句

查询词典 pin hole

与 pin hole 相关的网络例句 [注:此内容来源于网络,仅供参考]

A method of preparing the size-controllable and uniform capsules or beads by using pin hole with superposed air was proposed.

建立了一种通过气流作用于针头出口处的液滴,来制备比较均一的、可控尺寸微胶囊的方法。

And plumb line to locate drawbar pin hole.

电车线和铅垂线去定位拉杆销孔。

Electron/hole pair for every 3.62 eV of energy lost in the silicon, which is the input signal.

典型的探测器是Si-PIN光电二极管探测器:X射线与硅作用,使其平均每消耗3.62 eV能量便产生一个电子/空穴对,即为输入信号。

One such crack formed on the net section at the pin hole, much like an eyebar failure.

形成在销钉孔净截面处的一条裂纹非常象眼杆破坏。

Main features:- Hole spacing 2.25mm-operating voltage: 4.5 V to 24 V-switching offset compensation at 62Hz under - over-voltage Protection - VDD-pin Reverse voltage protection - Short circuit protection open-drain output is hot off - working magnetic field range: DC to 10kHz-output goes low with magnetic south pole contacts marked on the package side, while the higher magnetic flux density and area of S1, As S2-all temperature and supply voltage range magnetic parameters on-chip temperature compensation circuitry of the minimum drift - EMC meet DIN40839.

主要特点:–霍尔片间距2.25mm–工作电压: 4.5 V 至 24 V–开关偏移补偿在62Hz下–过电压保护– VDD-pin反向电压保护–短路保护漏极开路输出被热关断–工作磁场范围:直流到10kHz–输出变低用磁场南极接触封装上有标记边,而更高磁通量密度面积S1,如同S2–全温度和供电电压范围下磁参数的片上温度补偿电路的最小漂移– EMC适应DIN40839。

Development of a automatic CNC machine's control system for boring piston pin hole.

全自动CNC镗削活塞销孔专机控制系统的研制。

Research and development of full automatic CNC special machine for boring piston pin hole.

全自动CNC镗削活塞销孔专机的研究开发。

Research on machining principle for non-cylinder piston pin hole based on GMM.

基于GMM的活塞异形销孔加工原理研究。

There is a pin hole between outside shell and output axis.

外套与输出轴的径向有一个插销孔。

Load increased on piston,unreasonable design of piston pin boss,unevenly distributed positive stress on pin hole,stress on inside upper area of pin hole much higher than that on outside,the quality problem in machining and assembly are main reasons of fracture of steel-topped aluminium-skirted piston skirt .

活塞承受的负荷不断提升,活塞销座设计不合理,销孔正应力分布不均匀,销孔内侧上方区域应力远高于外侧应力以及加工和装配中存在的质量问题是柴油机钢顶铝裙组合活塞裙部裂损的主要原因。

第1/7页 1 2 3 4 5 6 7 > 尾页
推荐网络例句

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面,更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值,分为几个相等的区间作为横轴,并将各区间内所测定值依所出现的次数累积而成的面积,用柱子排起来的图形,也叫做柱状图。

You rap, you know we are not so good at rapping, huh?

你唱吧,你也知道我们并不那么擅长说唱,对吧?