查询词典 pin gear

"Belaying pin:a short, removable wooden or metal pin fitted in a hole in the rail of a boat and used for securing running gear."

系索栓：可插入船栏的洞内以固定船只的一种短的，可移动的木拴或金属栓。

"Belaying pin:a short, removable wooden or metal pin fitted in a hole in the rail of a boat and used for securing running gear ."

系索栓：可插入船栏的洞内以固定船只的一种短的，可移动的木拴或金属栓。用低挡上山。

Taking cydid gear-pin rail chainless traction mechanism of MG375W as an example, make theoretical deduction for the profile and the kinematic characteristics of the cycloid gear , and make simulation analysis for some different engaging positions by computer.

以MG375W采煤机的摆线轮与销排无链牵引机构为例，进行了摆线轮齿廓特性及运动特性的理论推导，对不同的啮合工位进行了计算机模拟仿真分析，得出了中心距及节距发生变化引起啮合传动特性的变化规律。

On the basis of the modification theory, relative modification concept of cycloidal gear pair and the appraisal index of the initial backlash are built to solve the problem that cycloidal gear works unsmoothly in pin wheel of the full-hydrostatic steering control units. The major goal of modification is a uniformity of initial backlash, so equidistance modification that has good effect on improving quality of fluid cycloidal pair is chosen.

为解决全液压转向器转子转动不灵活的问题，在分析现有摆线针轮啮合副齿廓修形理论基础上，建立摆线副修形的相对性概念和间隙分布评价指标，提出无系杆摆线副修形的主要目标应使初始间隙分布均匀，选择的修形方式为等距修形。

The methods for calculating the diameter of safety pin, fit clearance between the sleeve and hole in the planetary gear, and the quantity of the lubricants filled in the gear mechanism are presented.

供料系统根据钻井液密度的变化对钻井液流量的控制，电控系统在启动和停机时的程序控制，以及停机时的自动冲洗，都将直接影响整机的使用性能。

There are several manual steering gears in current use like the rack and pinion type ,the worm and tapered pin steering gear ,and the worm and roller steering gear.

目前使用的手动转向齿轮机构就是有好几种，如齿条齿轮式转向机构、蜗杆斜销式转向机构以及蜗轮滚柱式转向机构。

The RV reducer,which is a planetary gear system with cycloidal gears in contact with pin type internal gear teeth and involute gear pair,has been widely used as reduction gears of industrial robots, By reason that robots are very strict with vibrations,a dynamic model of RV reducer is developed.

建立RV减速器的动力学模型并推导运动微分方程，通过求解振动方程得到系统的固有频率，并就针轮齿数对RV减速器振动的影响等进行了研究，得到对RV减速器的设计和应用具有指导意义的结论。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

This paper put forward the method of calculating the number over teeth and pin diameter on the great addendum modification gear,and gave the number over teeth and pin diameter caIculation formulas easy to use in the work with curve fitting method.

文章提出了解决大变位齿轮跨齿数计算和量柱直径选取中存在问题的方法，给出了计算公式，用曲线拟会方法得出了便于使用的大变位齿轮跨齿数计算公式。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。