查询词典 pile hammer

Two groups of field tests on original soil and the soil among piles ,three groups of field tests on single pile ,one-pile and three-pile composite foundation have been conducted and the results of the bearing capacity ,as well as the elastic modula of each pile and composite foundation are obtained.It can be seen that soft earth reinforced by cement-soil piles seem to have better appearance in bearing and deforming than original one.

通过桩间土、原状土各两组，单桩，单桩与多桩复合地基各三组的现场静载荷对比试验，获得了各自的容许承载力值，根据P-S曲线计算出的变形模量结果表明，地基经过粉喷处理后，地基力学性质和变形特性得到明显改善，土层的强度和变形模量明显提高。

According to fully expounding the geologic condition of the location of the bridge and the structure of pile foundation and the research level of the bearing capacity of group pile foundation in the present, the paper analyzes the mechanism of group effect and the impact on bearing capacity of pile foundation. The finite-element numerical analyses and self-balanced method are adopted in the present paper to calculate and analyze the vertical bearing capacity of pile group of north main-tower is cleared up and analyzed.

在全面阐述桥位区工程地质条件和桩基础组成结构以及群桩基础承载力研究现状的基础上，深入探讨了群桩效应及其对桩基础承载力影响的机理，分别采用自平衡试桩测试技术和三维土工有限元模拟方法研究了单桩竖向承载力问题，通过对试验和计算结果的整理、对比分析，确定了能够客观反映地基土工程特性的地基土计算参数。

According to the basic principle of self-balanced pile test method and the conversional simplified conversion method, the pile bearing capacity between the equivalent loaded piles and self-balanced piles were compared. The influence of negative skin friction on self-balanced pile test was studied. The conversion formulas of pile bearing capacity and settlement were derived.

根据自平衡测试法的基本原理，在传统简化转换法的基础上，通过等效受压桩和自平衡试桩上下桩段受力情况的对比分析，研究了负摩阻力对自平衡测试原理的影响，推得了桩承载力和位移的转换公式。

The time-history velocity response signal of pile can be decomposed by Sym wavelet. The power spectrum value can be extracted from some specified spectrum range. These values from one signal makes up the characteristic vector representing this signal. The relationship between characteristic vector of pile and pile defect type can he established by using BP artificial neural network. Abundant time-history velocity response signals of pile can be acquired by numerical simulation method.

利用Sym小波对基桩速度响应时程曲线进行小波分解，对指定频带上的信号分量进行特征值提取，提取的特征值为反映各频带范围内体现能量分布的功率谱均值，提取的特征值可构成反映信号特征的特征向量，同时利用BP人工神经网络的非线性映射特性建立特征向量和基桩缺陷类别之间的一种对应关系。

If you have any forging equipment required and technical support, please call us: Anyang Forging Machinery Industry Co., Ltd.(electric air hammer-hydraulic hammer with the existing national standards for the drafting of the development of units), the only two tons tons of air hammer manufacturers to develop!

如果您有任何锻造设备方面的需要和技术支持请致电我们：安阳锻压机械工业有限公司（空气锤电液锤现行国家标准起草与制定单位）国内唯一2吨吨空气锤研制生产商！

This design introduces a fully mechanized coal face reproduced hammer crusher and hammer crusher of principle, structure and application: hammer crusher for crushing all kinds of hardware and erosion of weak materials.

本设计主要介绍了综采工作面转载锤式破碎机，以及锤式破碎机的工作原理，结构与应用：锤式破碎机用于破碎各种中硬且磨蚀性弱的物料。

PCFK series of pairs of counter-reversible hammer crusher is a new crushing equipment, mainly by knock-on effects to broken materials, broken process in general is this: the material falling into the break in the world, imported high-speed rotation of the hammer impact face was against the entrance of the adjustable crusher tooth wear plate, for the first time broken, broken after the particles basically the same material evenly into the main break, the secondary primary crushing, crushing in the main chamber has been uniformly The material was re-kinetic energy particles from the hammer, high-speed rushed back inside the jagged cavity lining was broken, due to the special lining sawtooth-shaped structure.

PCFK系列可逆双反击锤式破碎机是一种新型破碎设备，主要是靠冲击作用来破碎物料的，破碎过程大体是这样的：落下的物料进入破世界进口后，遇到高速旋转的锤头冲击而被打击到破碎机进口处的可调耐磨齿板上，进行首次破碎，破碎后颗粒基本相同的物料均匀的进入主破碎内，进行二次主破碎，在主破碎腔内已被均匀的物料颗粒从锤头再次获得动能，高速冲向反击腔内部的锯齿形衬板而被破碎，由于衬板特殊的锯齿形结构。

With 3.0 t empty dual-use steam forging hammer, 1.0 t empty dual-use steam forging hammer, 750 kg, 400kg, 250kg, 150kg Kong Qichui a total of seven, made 3.0 t, 2.5t of a hammer plywood Taiwan, the construction of 2 m × 1.5m × 1.0m two large coal-fired furnace, a gas generator furnace, resistance furnace, Oil Furnace, Meilu stoves and other heat treatment of the four sets, with the following specs for Φ550 Saw 5,φ100 major fault Liu and other supporting material under the equipment, and has CW611250, T68, and other machining equipment, more than 60 species of vehicles, milling, planing, grinding, boring jobs complete, the main products φ820 × 60 × 1300 following the suppression of three products,φ273 high-pressure forging Billet-three links, all kinds of high-pressure-welded flange and 3.0 t following forging free, annual production capacity of 2400 t.

拥有3.0t空蒸两用模锻锤，1.0t空蒸两用模锻锤，750kg、400kg、250kg、150kg空气锤共7台，自制3.0t、2.5t夹板锤各1台，建造2m×1.5m×1.0m大型燃煤加热炉两座，煤气发生器加热炉1座，电阻炉、油炉、煤炉等热处理炉具各4套，拥有加工规格为Φ550以下锯床5台，φ100大型断料机等配套下料设备，且拥有CW611250、 T68等机加工设备60余种，车、铣、刨、磨、镗工种齐全，主要产品φ820×60×1300以下压制三通成品管，φ273高压锻制三通方坯，各种中高压平对焊法兰及3.0t以下自由锻件，年生产能力2400t。

The plant of Shanghai Dalong Hot-work Engineering Co.,Ltd is equipped with two sets of 5T Arc Furnace,one set of 15T vacuum refinery furnace,one set of 15T vacuum degassing VD installation,5T electrohydraulic hammer,3T steam hammer,1T, 560KG,250KG air hammer and over 30 sets relevant supplementary equipments of machinery process equipments,hot-work and non-destructive damage detection equipments.

上海大隆热加工工程有限公司的生产厂，拥有5T电弧炉二台套、15T德国产VODC真空精炼炉一台套、15T

The principle of programming is focused on easy understanding and good use. The basic calculating data of Dahuofang water diversion project is put into the program which the water hammer calculation begins.Part four, uses the advanced Bentley Hammer water hammer calculation software calculates several identical engineering conditions of Dahuofang water diversion project, and then compares the results with the results of programming calculation, and proofreads the accuracy of programming calculation.

程序编好后输进大伙房输水工程的基本计算数据就可以开始进行水锤计算。4、同时使用目前世界上比较先进的&Bentley Hammer&水锤计算软件，计算大伙房输水工程的几个相同工况，所得结果与编写程序计算的结果进行对比，对编写的程序的正确性进行校核。5、在证实了编写程序的正确性，公道性后。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。