查询词典 permissible error

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

It also can be used to measure the geometrical tolerance, such as straightness error, roundness error, cylindricity error, parallelism error, perpendicularity error, angularity error, coaxiality error, symmetry error and circular run-out error etc.

该仪器集机、光、电于一体，采用了新的光路系统和近些年最新的测量方法及数据处理方法，具有功能多、体积小、重量轻、操作方便、非接触测量、测量精度高等特点。

In this paper, some characteristic functions of the multifunctional single-flank mesh gear tester of model CD320G-D which is applying gear integrated error measuring technique, computer technique, error separation technique, fault diagnosis technique and error prediction technique, including automatic searching of profile error start point, determination of profile barrelling, separation of profile form error and profile slope error, measurement of profile error with evaluation range subtracting tooth tip, measurement of tooth topograph and statistical analysis of gear manufacture error, are presented.

阐述了综合应用齿轮整体误差测量技术、计算机技术、误差分离技术、故障诊断技术和误差预报技术的多功能 CD320G-D 型单啮仪的一些具有特色的功能。这些功能包括齿形误差起测点的自动找定、凸形齿凸形量的测定及其形状误差与倾斜误差的分离、取值范围扣除齿顶部的齿形误差的测量、齿面轮廓度误差的测量以及齿轮加工误差的大样本统计分析。

Second, the data checking and correction process, to understand the various sources of measurement error, its three main areas: equipment error (determined by the instrument itself, is an objective source of error), observation error (due to the technical level personnel a result of belonging to a subjective source of error), external influence error (subject, such as temperature, atmospheric refraction effects of external factors such as these factors are also constantly changing and difficult to control, belonging to a variable source of error).

其次，在对数据的检查和矫正的过程中，明白了各种测量误差的来源，其主要有三个方面：仪器误差（仪器本身所决定，属客观误差来源）、观测误差（由于人员的技术水平而造成，属于主观误差来源）、外界影响误差（受到如温度、大气折射等外界因素的影响而这些因素又时时处于变动中而难以控制，属于可变动误差来源）。

To analyze the pseudo phenomena caused by migration velocity error, the paper firstly studied the depth error between post-stack migration and prestack migration caused by same velocity error, and found the depth error was only relative to velocity error and had no direct matter with methods of depth migration (post-stack migration or prestack migration). Then the paper did numerical simulation of a complex lenticular body model with wave-equation modeling and migration, and found that the velocity error could not only induce depth error, but also could change the modality of construction and the event of subjacent layers. Furthermore, it could change the frequency of reflective event. They are the pseudo phenomena caused by migration.

从分析偏移速度误差带来的各种假象出发，本文首先对比分析了速度误差对叠后深度偏移和叠前深度偏移的影响，发现偏移剖面的深度误差仅与速度模型的误差有关系，与具体的偏移方法没有直接的关系；然后对一个复杂的透镜体模型进行了波动方程叠后正演和偏移计算，详细地讨论了不同的速度误差带来的各种假象，发现速度误差不仅会带来深度误差，而且会造成构造体的形态变化，下覆地层同向轴的扭曲，还可能引起地层同向轴的频率发生变化，给资料解释带来一定的假象。

Error analysis In order to analysis the pose error of the hexapod machine tool, considering the characteristics of the parallel mechanism,"analysis on the error prominency factors for the hexapod machine tool pose error"is proposed. Numerically, the error prominency factor can express the influence on the pose error of the tool resulted from the mechanism parameter error within the whole workspace.

四、位姿误差分析为了定量地对并联机器人机床位姿误差进行分析，结合并联机构的特点，首次提出了&并联机器人机床位姿误差放大因子分析法&，因位姿误差放大因子是反映机床机构参数误差对刀具末端误差影响大小的机床工作空间内的统计值，因此既可作为机床结构参数精度设计的依据又可对机构参数进行优化。

Result］ It could be concluded through analyzing the model that both the mass uncertainties of quinoline phosphomolybdate precipitates and tested samples were from the resolving power and precision of balance and its maximum tolerance in assay certificate; the uncertainty brought in by volumetric flask was from the permissible error of 250 ml volumetric flask, the operation of increasing the volume to scale of volumetric flask while diluting solution and the difference between experimental temperature and the temperature at the time when the volumetric flask was calibrated; the uncertainty brought in by pipette was from the permissible error of itself, the operation of increasing the volume to intake scale while taking solution and the difference between experimental temperature and the temperature at the time when the pipette was calibrated.

结果］磷钼酸喹啉沉淀和试样质量的不确定度均来自天平的分辨力、精确度、鉴定证书上天平的最大允差，容量瓶引入的不确定度来自250 ml容量瓶本身的允许误差、稀释溶液时将体积增加到容量瓶刻度的操作和试验温度与容量瓶校准时温度的差异，吸量管引入的不确定度来自于吸量管本身的允许误差、吸取溶液时将体积增加到吸取刻度时的操作和试验温度与吸量管校准时温度的差异。

Error Analysis of UGPS Error sources of UGPS include GPS observation error, attitude error, baseline network strength, sound velocity error, time measuring error.

系统的误差分析实现水下的精密定位，需要分析影响系统定位的各种因素。

On the basis of the study on the mathematical model of the closed-loop location control, the analysis of contour error in the process motion control and error calculation model, according to the lack of using normal contour error model not to calculate contour error of curve in real-time, combining real-time contour error compensation control strategy and fuzzy logic theory, the fuzzy logic and real-time contour error calculation based self-discipline control strategy is proposed.

2在研究闭环位置控制数学模型、加工轮廓运动控制中的误差分析和轮廓误差计算模型的基础上，针对利用一般运动轮廓误差计算模型不能实时计算出曲线轮廓误差的不足，结合实时轮廓误差补偿控制策略和模糊逻辑理论，研究了基于模糊逻辑理论和实时误差计算的轮廓自律控制策略。

The evaluation method and algorithm of shape error (roundness, plane straightness, space straightness, cylindricity) were discussed. A new kind of algorithm, namely mesh searching method, which can be used to evaluate the roundness error, plane straightness error, space straightness error and cylindricity error, were put forward. With this algorithm, the shape error can be obtained by transferring the distance formula repeatedly and simple judgment without linearzing the distance formula (from point to point or point to line) and choosing optimal direction and step length.

对形状误差(圆度、平面直线度、空间直线度、圆柱度)的评定方法及算法进行了讨论，提出了一种评价圆度误差、平面直线度误差、空间直线度误差及圆柱度误差的新算法——网格搜索法，该算法不需要对距离公式线性化，也不需要选定优化方向和优化步长，只需重复调用距离公式和简单的判断即可得到符合定义的形状误差。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？