查询词典 parameters

According to the principles of tooth meshing and manufacturing helicoi ds, a mathematics model is constructed to reflect the manufacture process of nut , and the formula of the grinding wheel section is developed. The parameters of the section are obtained through numeral arithmetic; moreover the parameters of the dresser are worked out. Based on these work, the solid model of the ball scr ew nut, grinding wheel and tooth dresser are developed in the Pro/E software, wh at's more, the process of the dressing...

根据螺旋面加工原理、齿形啮合原理及回转面砂轮加工螺母工艺建立了相应的数学模型，并推导出砂轮截形的计算公式；采用数值计算方法求解砂轮截形参数，进一步得到修整器靠模板的参数；在此基础上，利用Pro/E软件对大导程滚珠丝杠螺母、砂轮和砂轮修整器进行了实体建模，并对砂轮的修整过程和螺母的加工过程进行了运动仿真，有效地验证了砂轮截形的计算结果。

Introduces a switching step-response algorithm parameters of the self-tuning controller, through the actual temperature control systems, Relay oscillation parameters and self-tuning algorithm and the parameter auto-tuning analysis module, The algorithm proves the safety and setting time than the other two algorithms.

详细说明：介绍了一种基于开关阶跃响应算法的参数自整定控制器，通过在实际温度控制系统的应用，与继电振荡参数自整定算法以及的参数自整定模块进行分析比较，证明该算法在安全性及整定时间上明显优于其他两种算法。

The introduction of some products are as follows: First, Taiwan's electronic devices Aosta Product:(self-produced self-marketing) program-controlled voltage insulation tester, grounding resistance, leakage current, micro-resistance tester, electrical parameters of the test Transformer parameters meter, insulation resistance tester, electronic load, on-machine, cable tester, variable frequency power supply, LCR Bridge, frequency meter, mV table, the standard signal generator, oscilloscope, signal generator, signal generator, digital multimeter, distortion device, before shaking device, spectrum analyzer, capacitance meter, inductance meter, modulation device, Sweep Signal Generator, Telephone Analyzer, Calibrator Table III, EMC Electric Tester, regulated power supply and so on.

现将部分产品介绍如下：程控耐压绝缘测试仪、接地电阻、泄漏电流、微电阻测试仪、电参数测试变压器参数测量仪、绝缘电阻测试仪、电子负载、导通机、排线测试仪、变频电源、LCR电桥、频率计、毫伏表、标准信号源、示波器、信号发生器、信号源、数字万用表、失真仪、抖摆仪、频谱分析仪、电容测量仪、电感测量仪、调制度仪、扫频信号发生器、电话分析仪、三用表校准仪、EMC电测仪、稳压电源等。

Moreover, sum up the modeling method and step for tap;The paper focus on the tapping speciality of screw tap, and the influence between geometrical parameters and cutting performance, targeting the minimum tapping and axial force, the optimum design of geometrical parameters is done, especially the flute shape.

论文重点研究了螺旋槽丝锥的攻丝特性及其几何参数对切削性能的影响，基于最优设计原理建立了攻丝扭矩最小及轴向力为零的双目标非线性优化模型，并利用Matlab软件，对螺旋槽丝锥的几何参数，尤其是丝锥容屑槽槽形，进行了优化，根据优化结果建立了丝锥的三维CAD造型。

This paper introduced the parameter frequency response method,developed ship rolling frequency response function equipped with two U-tube anti-rolling tanks with different natural frequencies,analyzed the tank parameters relative to rolling frequency response amplitude,and researched the effect of tank parameters on the ship rolling amplitude.

本文给出了参数频率响应法，推导了装备两个具有不同固有频率的被动式U型减摇水舱的船舶横摇频率响应函数，分析了影响船舶横摇频率响应幅值的水舱参数，通过仿真详细研究了水舱参数对船舶横摇减摇的影响。

The lift course of hanging device on wheat no-tillage planter was simulated by using the software of ADAMS. Some important parameters were obtained such as height of the working part relative to ground, the distance between the working part and the rear wheel of tractor, the angle of road pass and the force of hanging point, etc. The key parameters of the hanging device and its best working parameter of hanging device were found out through optimization simulation. Simulation results showed that suspension point had minimum force when variable DV_1 and DV_2 gained corresponding maximum and minimum at scope of structure limit.

应用ADAMS软件对小麦免耕播种机悬挂机构提升过程进行了动态仿真，得到了工作部件的位置高度、工作部件与拖拉机后轮之间的间距、路面通过角以及悬挂点的受力等参数，找到了悬挂机构的关键参数，通过优化仿真，得到了悬挂机构的最佳工作参数，仿真结果表明，设计变量DV_2、DV_3在结构受限范围内分别取其最大值和最小值，悬挂机构悬挂点受力最小。

Through documents checking and data collecting,this paper analyzed the items and values of input/output parameters of N cycling in stock farming system,and ascertained the estimation parameters of N balance in the system,which could offer the theoretical foundation for nutrient management in animal husbandry ...

本研究对该系统的N输入、输出项参数进行分析讨论，包括平衡计算中每一个输入和输出项需要的参数种类、参数的选择以及建议采用的数值。讨论过程参考了大量的文献资料和统计数据，初步确定了我国畜牧系统N养分平衡计算参数。

If the parameters for the function require more than seven registers, the additional parameters are stored on, and passed to the called function, using the stack - a cycle-intensive process that degrades performance and leads to increased RAM usage.

如果函数所用到的参数需要7个以上的寄存器，那么这些多出来的参数就被存储，并且通过堆栈传给调用函数-需要1个周期的过程，这样做降低了性能并且增加了对RAM的使用。

Research on parameters of mechanical model for high speed railway truck is performed and the calculated formulas and the value ranges corresponding to these parameters are given in this paper.

对高速铁路轨道结构力学模型中的参数进行了研究，给出了各参数计算公式和取值范围。

Eddy current proximity switch ; structural parameters ; electromagnetic parameters ; speed indicator

涡流接近开关；结构参数；电磁参数；测速计

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。