查询词典 parallel angle

The study of dynamic evolvement course of Yarlung Zangbo River (the parallel water system on back edge of collided strap) on Himalayan block boundary and response to structure action is a bran-new angle.

研究喜马拉雅板块边界上雅鲁藏布江在板块边界上的动态演变过程及对构造活动的响应是一个全新的研究角度。

A systemic research on the birefringence of side-hole fiber is presented. The research results show that the birefringence of circular-core side-hole fiber relies mainly on stress birefringence, its fast axis is parallel to the link line of the two holes, and its intrinsic birefringence increases exponentially with the angle and ellipticity of side holes.

本论文的主要研究结果和创新在于： 1、对边孔光纤的双折射特性进行了系统研究，提出圆芯型边孔光纤以应力双折射为主，两边孔连线方向为其快轴方向，其双折射大小与边孔张角和边孔椭圆度成指数关系。

The influence of stagger angle of axial flow fan upon the operation performance of parallel running was obtained.

该文在2台风机并联运行的基础上，绘制并联风机的性能曲线，获得叶片安装角对并联风机运行特性的影响。

Nonlinear projection method with changing angle for parallax introduction is put forward on the basis of parallel projection method and logarithm projection method.

在平行光投影、对数投影引入视差方法的基础上，提出了实用的变角度的非线性引入视差法。

The magnitude of current reaches maximum when the incident angle is max (namely, the incident wave is parallel to the strip of MSTL).

在模拟过程中，本文对模型建立、端口设置、激励源设置方法进行了细致深入的研究，给出了终端为短路、匹配、开路三种情况时的有效解决方法。

Even though actual data for impingement angle are not available so far, it can be considered as spectrum of low impingement angles when the water is flowing almost parallel to the surface.

虽然目前没有什麼实际的资料可以验证粒子角度的影响，但当水的流动跟表面几乎是平行时，角度影响的幅度相对的会比较低。

In order to get the largest possible field of view, low magnification eyepiece multi-use wide-angle eyepiece, depending on the field in general is greater than 3 °, FPA Office for aiming with the reticle with its optical axis to remain parallel with the primary mirror optical axis.

通常为口径小于10厘米的折射望远镜。为了得到尽量大的视场，目镜多选用低倍率的广角目镜，视场一般大于3°，焦平面处装有供瞄准用的分划板，它的光轴要与主镜光轴保持平行。

Through two parallel movement in the right-angle's guarantee of imposition of accuracy.

堵住两把可交错移不静的直角钢尺包管拆版的不确性。

The converse method is used to determine the parameters in the design of the parallel machine tool,which allows the use of maximum range of machine varibales(e.g.swinging angle of spherical bearng)within their limits.

机床设计参数的确定采用逆向设计法，充分利用了已有机床部件的极限参数。

Fig. 1. The plan and side view of the flow of a molten polymer liquid in gas-assisted injection molding where a pipe is connected vertically to line A to a fan-shaped cavity with a vertex angle of 180度 formed by two parallel plates and gas is injected at the point above where two cavities are connected.

图。 1。该计划和侧面的熔融聚合物液体流动的角度在气体辅助注塑成型在管道连接垂直线A到一个扇形腔一顶点由两个平行板和气体形成的夹角为180度在上述点注入其中两个腔相连。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。