查询词典 paper size

The handwriting feature is: font smaller; the length of the font size ranging from a stroke kerning, cross－section; infinitelysmall, close to the incessant; arranged irregular; character; the paper--you can see the characters have a slight depression, inks also bias.

其字迹特征是：字体较小；字体长短大小不一，笔画粗细不均；字距极小，紧密无间；排列不规则；漏字；纸面可见到字迹有轻微凹陷，墨色亦浓淡不一。

Riley (The 12 Days of Christmas, 1995, etc.) uses bold colors for her cut-paper collages and almost life-size proportions to include readers in the mouse's illicit feast. Cookies, crackers, and cornflakes join olives, peanut butter, and cheese, cascading like a waterfall from the counter to the kitchen floor.

作者瑞利在书中采用了浓重的色彩和剪贴画设计，将小老鼠偷吃的晚餐都按照正常生活中的比例呈现在读者面前，饼干啊、脆玉米片啊、橄榄啊、花生酱啊、奶酪啊像瀑布一样从厨房的餐台上一直散落到厨房的地板上。

Size and number of changes, in order to do accurate cutting devices, you must press the paper trays.

规格尺寸和数量的变化而变化，为了做到准确裁切，必须用压纸器将纸张压紧。

In order know the size and the distribution of residual stresses of mill welding seam,this paper uses blind-hole method to test the girth welds between round plate and the cylinder body of the mill produced by CBMI CONSTRUCTION CO.,LTD.

为了了解滑履磨机焊缝残余应力的大小和分布规律，该文应用盲孔法对中材建设有限公司生产的某型号磨机的圆平板与圆筒体之间的环焊缝及其近缝区的表面残余应力进行了现场测试。

In order know the size and the distribution of residual stresses of mill welding seam,this paper uses blind-hole method to test the girth weld s between round plate and the cylinder body of the mill produced by CBMI CONSTRUCTION CO.

为了了解滑履磨机焊缝残余应力的大小和分布规律，该文应用盲孔法对中材建设有限公司生产的某型号磨机的圆平板与圆筒体之间的环焊缝及其近缝区的表面残余应力进行了现场测试。

In order know the size and the distribution of residual stresses of mill welding seam,this paper uses blind-hole method to test the girth welds between round plate and the cylinder body of the mill produced by CBMI CONSTRUCTION CO.

为了了解滑履磨机焊缝残余应力的大小和分布规律，该文应用盲孔法对中材建设有限公司生产的某型号磨机的圆平板与圆筒体之间的环焊缝及其近缝区的表面残余应力进行了现场测试。

In this paper, a simple method and procedure is given by which cone radius, journal angle, diameter and leg datum point size of a rock bit can be calculated respectively according to geometric relations of rock bit structure parameters.

本文给出一种根据牙轮钻头结构参数间的几何关系分别计算牙轮半径，牙爪轴倾角，牙掌基准尺寸，牙轮背锥角和钻头直径的方法及程序。

As a result, the general approach is business card printing and membership card before the paper cutting into finished products expand the size, Business card printing and membership card after only indentation processing is no longer needed die-cut or.

因此，凡是拔取的办法是制卡和会员卡制作后不兵纸弛裁切成制品的伸开尺寸不小小，制卡和会员卡制作后只举行压痕增工，不一再必给裁切或模切。

The layer of solid KCl is so thin in depth、so small in size、 and so low in grade that it is too difficult to exploite it. Besides that, only 1/3 of the liquid KCl can be expoi ted due to the mining method of well and canal drainage which is being used now. Therefore, it is one of the key problems to exploite the liquid KCl as possible as we can and to turn the solid KCl into explo itable liquid deposit in Qarhan salt lake. So the idea of dissolving and driving exploitation has been suggested. This paper will deal with three problems as follow

然而由于固相矿层薄、品位低而难以直接开采利用，加之目前对液相矿产只是纯疏干性开采，充其量只能采出1/3的液相矿，因此如何最大限度地开采液相矿产，同时将固相矿产转化成能直接开采利用的液相矿产是察尔汗盐湖开采中急需解决的关键问题之一，对此人们提出溶矿驱动开采的设想，本文正是以此为目的，着重研究以下三个问题

This paper introduces the quality control in the production of huge cemented carbide six -face anvils,which are applicated to synthesize artificial diamond in large size capacity.

概述了与人造金刚石合成大腔体相配套的硬质合金六面顶大顶锤的质量状况，分析了大顶锤质量与使用寿命的关系，从内部结构和外部质量两方面讨论了大顶锤质量控制的方向，提出了提高大顶锤质量、降低锤耗的几种方

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。