查询词典 packing nut

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close the valve, the need to open and close with the Coma Berenices two pieces of the sealing surface of the seal formed between certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread Automatic Control Valves between the stem end bearing at and other friction parts of the friction, and therefore must apply the closing force and closing a certain moment, the valve in the open and close the process, the required hoisting hoisting force and moment of change, and its maximum is close to the final instant or open the initial transient.

关闭阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Close discharge valve, the need to open and close with the Coma Berenices two pieces formed between the sealing suce sealing certain specific pressure, while also overcoming the stem and the packing between the stem and the nut thread between the stem end Department and other friction parts bearing friction, and must exert a certain degree of closing force and closing moments, PUMP CONTROL VALVE EN700X the valve in the open and close the process, the required hoisting hoisting force and torque is the change, Its maximum is in the closed or open end of the initial transient instantaneous.

关闭放料阀门时，需要使启闭件与发座两密封面间形成一定的密封比压，同时还要克服阀杆与填料之间、阀杆与螺母的螺纹之间、阀杆端部支承处及其他磨擦部位的摩擦力，因而必须施加一定的关闭力和关闭力矩，阀门在启闭过程中，所需要的启闭力和启闭力矩是变化的，其最大值是在关闭的最终瞬时或开启的最初瞬时。

Valve:(dark-parallel) 1 - wedge-shaped gate valve; 2 - sleeve nut; 3 - Valve; 4 - stem; 5 - valve cover; 6 - Thrust Convex shoulder; 7 - Packing letter flange; 8 - packing; 9 - Packing Gland, 10 - hand wheel; 11 - valve cover pad.

闸阀：1--楔形闸瓣；2--套筒螺母；3--阀体；4--阀杆；5--阀盖；6--止推凸肩；7--填料函法兰；8--填料；9—填料压盖；10--手轮；11--阀盖垫。

Clean and check 1 slowly loosen the gland nut stuffing, packing the release of residual pressure of all components; 2 Remove all old packing, thoroughly clean axle / rod stuffing; 3 Check the shaft / bar have corrosion, dents, scratches or excessive wear; 4 Check whether there are other WATER POWER CONTROL VALVE parts burr, cracks, wear, they will reduce the packing life; 5 Check whether there is too much stuffing the gap, and the shaft / rod eccentric degree; 6 the replacement of defective parts larger; 7 Check the old packing, as BALANCING VALVES the basis of failure analysis to find the reasons for early failure of packing.

缓慢松开填料函的压盖螺母，释放盘根组件内所有的残余压力； 2）移去所有旧的盘根，彻底清洁轴/杆的填料函； 3）检查轴/杆是否有腐蚀、凹痕、划伤或过度磨损； 4）检查其他零件是否有毛刺、裂纹、磨损，它们会减少盘根的寿命； 5）检查填料函是否有过大的间隙，以及轴/杆的偏心程度； 6）更换有较大缺陷的零部件； 7）检查旧盘根，作为失效分析的依据，球阀以找到盘根早期失效的原因。

The valve packing Manufacturer or to the FORGED STEEL VALVES packing company's technical department or consult the relevant provisions of torque compression percentage, the following steps to tighten the squeeze cap nut:(1) applied to the gland nut torque to full torque of 30% or the percentage compression of the party;(2) repeatedly open and close valves several times, when the valve is in the closed position, to exert all the torque;(3) Repeat steps (2) 3 or 4 times.

阀门用盘根向盘根制造商或企业的技术部门止回阀咨询有关扭矩的规定或压缩百分比，按以下步骤拧紧压盖螺母：（1）向压盖螺母施加扭矩至满扭矩的30%或是党的压缩百分比；（2）反复开闭阀门数次，当阀门处于蝶阀关闭位置时，施加全部扭矩；（3）重复步骤（2）3或4次。

Adjusting the packing 1 Pump packing (1) continue to hand tighten the squeeze cap nut;(2) after opening the pump, adjust the gland nut, this time to allow a little more leakage;(3) slowly tighten the squeeze cap nut, gradually reduce the leak until the leak to an acceptable level;(4) If the disclosure of a sudden stop, should be back to tighten the gland nut, packing re-adjustment in order to prevent overheating;(5) adjust the leakage rate can reach a steady state.

泵用盘根（1）继续用手拧紧压盖螺母；（2）开泵后，调整压盖螺母，此时截止阀允许有稍多的泄漏；（3）缓慢地拧紧压盖螺母，逐渐减少泄漏，直到泄漏达到可接受的程度；（4）如果泄露突然停止，应回拧压盖螺母，重新调节以防止盘根过热；（5）调节泄漏率达到一个稳定状态即可。

The packing nut of this valve is secured by a lock nut with left-handed threads which prevents accidental loosening of the packing nut.

通过一个锁定螺母来固定密封螺母。锁定螺母带有左手螺纹，可以防止密封螺母的意外松动。

By decomposition of the inverse order of loaded gland packing 50, spring washers 49, nut 48 fixed tight with the above-mentioned components.

9按分解的逆顺序依次装上填料压盖50、弹簧垫圈49，用螺母48固紧上述零件。

By decomposition of the inverse order of 50 loaded packing gland, stem stopper 66, spring washers 49, nut 48 fixed tight with the above-mentioned components.

9按分解的逆顺序依次装上填料压盖50、阀杆限位器66、弹簧垫圈49，用螺母48固紧上述零件。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。