英语人>网络例句>oxidation process 相关的网络例句
oxidation process相关的网络例句

查询词典 oxidation process

与 oxidation process 相关的网络例句 [注:此内容来源于网络,仅供参考]

REE geochemical characteristics and their systematic changes in the sedimentary section suggest that there existed a process of ingression-regression in this area in the early Cambrian period. The black shale series resulted from the mixing between normal seawater sediments and hot seawater sediments and were deposited under the transitional condition from reduction to semi-reduction and weak oxidation in a shallow-sea clinoform zone of a relatively deep sea environment with dry climate.

稀土元素地球化学特征反映该区早寒武世曾发生过一次明显的海侵-海退过程,黑色岩系为正常海水与热水混合沉积的产物,形成于缺氧还原状态过渡到半还原-弱氧化状态的过程中,沉积环境为干燥气候条件下相对较深的浅海斜坡环境。

The integrative oxidation ditch process is a new technology for domestic sewage disposal.

一体化氧化沟工艺是一种新型的生活污水处理技术。

This Al -free 980nm pump laser have many merits, such as improved catastrophic optical damage level; no degradation due to oxidation of aluminium during fabrication process and laser operation, which is desirable characteristic for multi-step growth; lower electrical and thermal resistance with GalnP cladding; better carrier confinement with GalnAsP confinement layers; Selective chemical etching between GaAs and GalnP maks precisely control for fabrication of stripe geometry lasers.· Calculated the physical parameters of ternary and quaternary III - V compoundsby interpolation formulas based on curve fits or on a linear regression, such aslattice parameter, band gap, and refractive index.· Using luttinger-kohn Hamiltonian-based propagation-matrix method presentedby S.L.

这种无Al980nm半导体激光器可以提高激光器出现腔面损伤所需的能量,消除在生长过程和应用过程中由于Al的氧化而使激光器的使用寿命缩短的问题,便于激光器的多次生长;以GaInP为盖层可以降低电阻和热阻;可以精确的控制GaAs和GaInP之间的化学刻蚀,便于激光器几何形状的控制。

However, such defect as crack, pore, oxidation and ill bonding between cladding layers might appear in RLF parts if the process parameters controlled improperly. And crack was a kind of defect, which was the most familiar and companied with the largest brisance.

但是,如果成形条件控制不当,易于在成形件中产生裂纹、气孔、夹杂、层间结合不良等缺陷,而裂纹是成形过程中最常见、破坏性最大的一种缺陷。

第26/26页 首页 < ... 18 19 20 21 22 23 24 25 26
推荐网络例句

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。

There is no differences of cell proliferation vitality between labeled and unlabeled NSCs.

双标记神经干细胞的增殖、分化活力与未标记神经干细胞相比无改变。