查询词典 optimum

Resultsthe best blanching time of cleaned angeleno was 4 min with 0.06 % vitamin c to stabilize color before extraction; the optimum parameters of enzyme treatment was as follows: dealing angeleno with 0.10 % pectinase at ph 4.0 and 50℃ for 4 h.

结果确定最佳热烫时间为4 min、维生素c添加量0.06 %；最佳酶处理条件：酶用量0.10 %，酶作用时间4 h，50 ℃，ph4.0；加2倍水榨汁，出汁率80.3 %。

The optimum making-up prescription of Angeleno and almond compoundprotein beverage is that: the ratio of Angeleno juice/almond slurry is 10:11, mixedemulsifier (span 60/tween 40=25:11) 0.13%, mixed stabilizer (xanthan gum/carrageenan=1:2) 0.12%, sugar 10%.

安哥诺李、杏仁复合蛋白饮料最佳配方：安哥诺李汁和杏仁浆的配比为10：11，复合乳化剂(HLB=8)(司盘60：吐温40=25：11)为0.13％，复合稳定剂(黄原胶：卡拉胶=1：2)为0.12％，蔗糖为10％。

This paper solved the optimum installed angle anchor bar in anchored joint by considering the shear dilatatility of joint and utlizing the Mises yield criterion.

本文根据基本理论分析，考虑节理的剪胀效应并利用 Mises屈服准则求解得出了加锚节理面抗剪的最优安装角。

In this paper, based on the specific CNG engine parameters and characteristics, the influence of the injection timing, ignition energy and lean combustion for the engine is tested, in order to explore the control rules of fuel injection, ignition energy and lean combustion and then draw the following conclusions: small injection advance angle of electronic controlled injection CNG engine is optimum

文章根据天然气发动机的具体参数和特性，探索电控喷射CNG发动机在燃料喷射、点火能量和稀燃等方面的控制规律，确定最优的控制参数，开展了喷射定时、点火能量及稀薄燃料等参数对发动机性能影响的试验研究工作，并根据试验结果分析，得出了以下结论：电控喷射WT615CNG发动机燃料喷射提前角要小些为宜

The calculations show that the approximation for the birefringence and the rotatory property of interaction material leads to an error in the optimum incident angle for TeO2 more than 10%, a diviation in fa-λ0 relation from experiment results, and make the spectral resolution and angular aperture of the device to be degrade.

结果指出，在该波长下，对晶体双折射取近似表达式和不计入晶体的旋光特性，对光波最佳入射角θi的选取(在θi小于60°的范围内)，将引入大于10%的误差，这个误差由于涉及到是否满足动量匹配条件，因此会对器件的性能有直接的影响。

Laser technique ; optimum design ; error analysis ; angular displacement

激光技术；优化设计；误差分析；角位移

The results showed that:①The optimum fermentation conditions of Monascus anka 5040 were 170 r/min table rotational speed, 32℃ temperature, pH5.4 and 90 mL/L load.

结果表明：①红曲霉菌5040发酵的最佳工艺条件为摇床转速170r/min，温度32℃，pH 5.4，接种量90 mL/L。

The optimum annealing temperature is between 700 and 750℃.

实验结果表明，700~750℃范围为最佳退火温度。

Under the conditions of stir speeds 400 r·min~(-1) and distance between anode and cathode 1 mm, by using the orthogonal design, the optimum technological conditions were found that the current density was 0.3 A·cm~(-2), initial NaOH concentration in catholyte was 50 g·L~(-1), reaction times of two steps were all theoretical electrochemical reaction times. In the first electrosynthesis, initial Na_2CrO_4 concentration in anolyte was 650 g·L~(-1), and reaction temperature was 80℃. In the second electrosynthesis, initial Na_2Cr_2O_7 concentration in anolyte was 700 g·L~(-1), and reaction temperature was 85℃.

324全氟磺酸增强复合阳离子交换膜、阴阳极液中搅拌速度均为400r·min~(-1)条件下，通过正交实验得到优化工艺条件为：电流密度0.3A·cm~(-2)，阴极液氢氧化钠初始浓度50g·L~(-1)，两步反应时间均为理论电催化反应时间，第一步阳极液铬酸钠初始浓度650g·L~(-1)，反应温度80℃，第二步阳极液重铬酸钠初始浓度700g·L~(-1)，反应温度85℃。

The mechanical property testing shows that the seamless PLLA tubes perform excellent radial strength,which indicates that the mechanical properties of biodegradable stents made of these tubes was supposed to be excellent.PLLA and its composites were first used in preparing seamless tubes as antecedency of laser-cut biodegradable coronary stents in china.Finite element analyses of the biodegradable coronary stent model indicate the explorative design basically meets the requirement of reasonable and applicable stents.There is not such kind of research yet in domestic.Optimum laser-cuttting parameters of CO2 laser was cauculated based on experiential formula,within it,biodegradable coronary stents,especially those with complex structure would be manufacutured from seamless tubes quickly by laser microprocessing with high consistency to the design model.The processing efficiency of the CO2 laser demonstrated in experiential formula by us will play an important guiding role in manufacturing biodegradable stents by laser-processing.Our stents that ascribed to laser-cutted,slotted tube stent are proved to be biodegradable, self-expandable and good biocompatible,basically reach the international level on the aspest of manufacturing procedures and design.

研究结果表明：壳聚糖改性材料综合性能优于纯PLLA，更适合于作为可降解冠脉支架的原材料；自主设计的探索性自膨胀管状闭环型可降解冠脉支架的性能符合冠脉设计要求，设计、验证生物可降解冠脉支架模型的研究在国内还未见报道；制备的改性PLLA无缝管的力学性能优越，可通过激光切割获得冠脉支架，这是国内首次采用聚乳酸材料来制备通过激光加工出可降解冠脉支架的无缝管；二氧化碳激光器加工精度能达到加工要求，加工出来的血管支架名义设计与实测值误差小，实现了冠脉支架、尤其是带有复杂外观设计冠脉支架的快速化、规范化加工，对二氧化碳激光器加工聚乳酸材料的效果研究在国内外属于首创，获得的经验公式对日后的深入研究有重要的指导意义；制备的支架为激光切割管状闭环型冠脉支架，支架外观设计、支架加工手段、支架的性能都基本接近国际水平，支架样品符合设计的理念，可以实现自膨胀功能。

I think people in this lifetime in a rebirth.

我觉得人在这一生里其实也在轮回。

He had to tie her hands together.

他不得不把她的双手绑在一起。