查询词典 optimal process

The main research focused on the optimal Lingnania chungii McClure CEP 's explosion process and the effect of process parameter on chemical constitutes of explosion pulp .

本研究主要探讨了粉单竹爆破制浆的工艺条件、制浆过程中化学成分的变化、粉单竹爆破浆的漂白性能的研究以及其配抄新闻纸和包装用纸的性能。

The experiment results indicate that: the increases of catalyst concentration, feed mole ratio of methanol to formaldehyde and the decrease of total feed flow can increase the yield of methylal; the concentration of methylal in distillate also increases with the increase of catalyst concentration; that the effects of reflux ratio on the yield and concentration of methylal in distillate are different from conventional distillation process, an optimal value of reflux ratio exists between 1 and 2 for this process.

实验结果表明：回流比对甲缩醛收率和塔顶甲缩醛纯度的影响不同于一般的精馏过程，存在一个最优回流比，本过程最佳回流比在1-2之间；提高催化剂浓度，甲缩醛收率和塔顶甲缩醛纯度均增加；提高进料醇醛摩尔比也会提高甲缩醛收率；进料总流量对甲缩醛的收率的影响十分明显，进料总流量减少可以使甲缩醛的收率得到明显提高。

On the design of algorithms, a novel exact hierarchical delay analysis method for general circuits is proposed; based on the sensitization theorem for sequential circuits, an exact minimizing clocking method is proposed; based on Boolean process, a waveform simulation method considering interconnecting delay for logic circuit and a parallel waveform simulation method are proposed; a new method that transforms bit-level waveform polynomial to word-level polynomial model is proposed; a multiple valued synthesis algorithm based on multiple valued Boolean process and a wire-centered delay synthesis policy are proposed, in which timing planning, floorplanning, wire planning and optimal clock skew in early design are considered; a two-layers channel routing method for minimizing crosstalk under grid mode is proposed; based on the transition numbers theorems for waveform polynomial, a new method for generation of test with noise effects is proposed.

算法设计方面，提出了一种精确的通用电路层次化延时分析方法；基于时序电路的敏化定理提出时序电路最小时钟周期精确确定方法；提出基于Boolean过程论的考虑互连延迟的逻辑电路波形模拟方法，在分析了波形模拟适合并行化基础上，进一步提出一种并行波形模拟算法；提出一种将位级电路波形多项式描述转化成字级多项式描述的新方法；提出一种基于多值Boolean过程的多值电路综合算法以及一种将前期设计定时规划、前期设计的布局规划和线网结构化方法及低偏移的时钟分配等技术相结合的面向互连延时的综合策略；提出一种串绕最小化的网格模式下的双层通道布线方法；从波形多项式描述跳变数的定理出发提出了一种考虑噪声效应的测试生成新方法。

Based on the whole trip-reclosure process and considered the two important targets,the stability of power system and the shaft torsional oscillation of generators,a scheme of optimal trip-reclosure process were all proposed.

针对输电线路继电保护跳闸—重合闸电气操作全过程，综合考虑电力系统稳定性和发电机轴系扭振两项指标，提出了最佳跳闸—重合闸过程。

In the process of evaporation, under the direction of phase diagram method, the main purpose is how to separate kinds of salt by-product, enrich Lithium, decrease the ratio of Mg/Li. The study shows that the Lithium can be concentrated to about 0.8%, the ratio of Mg/Li can be lowed to 10; In the process of precipitating, in order to separate the left Magnesium and Lithium, a lot of experiments were carried out with the Sodium carbonate or Calcium hydroxide and Sodium Sulfate anhydrate as precipitator of Magnesium, where the separation results were compared, and an optimal separation idea was proposed.

在蒸发阶段中，以相图分析为理论指导，着重研究了如何利用自然能源蒸发卤水，提取有用的镁盐和钾盐，并达到富集锂盐的目的，在此研究中，锂的浓度可富集到0.8％左右，镁锂比可降到10以下；在沉淀阶段中，分别研究了用纯碱、石灰乳和芒硝作为沉淀剂来分离镁锂，比较了分离效果、提出了最佳分离方案。

In chapter six, the vender markov process and renewal process are used to analyze deteriorating items inventory control .The steady balanceable target function is established and the optimal inventory control strategy is given.

第六章引入向量马氏过程和更新过程对随机易腐物品的最优存储进行了基本分析和探讨，给出了模型从稳态下的目标函数，并提出了最优的库存控制策略。

Finally, simulation software was developed with Visual C++ and Delphi for 2D molding analysis of MIM, which affords facilities for the quality forecast of 2D thin wall parts and optimal design of mold and process parameters. In the research of molding performance of MIM feedstock, for the shortcoming of capillary rheometry, it was propounded that using spiral mold test molding performance of feedstock, and a set of spiral mold was creatively designed with quickly exchange gates and closed mold cavity. With the spiral mold, an orthogonal experiment was made on getting regress equation of flow length L〓 of the heavy alloy feedstock. Then the rule of L〓 varying with Q〓, P〓, and ΔT〓 was discovered. Q〓 ranks first in the influence on process parameters of molding performance, P〓 and Δ T〓 second. Therefore the injection rate Q〓 should be controlled primarily to improve the flow performance of feedstock.

在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L〓的回归公式，揭示了L〓随Q〓、P〓、△T〓和S〓的变化规律，并得出工艺参数对成形性能影响的强度顺序为Q〓最大，P〓与△T〓其次，因而改善喂料流动性能应优先控制注射速率Q〓。

By process testing, we discovered the optimal rigidity matching value of friction 30CrSiMoVA Steel with the powder metallurgy material, and put forward an new heat treatment process.

通过工艺试验，找到了30CrSiMoVA钢与某粉末冶金材料相互磨擦时的最佳匹配硬度值，提出了一种热处理新工艺。

Moldflow software was used for searching for optimal parameter of forming process of ABS gusset plate by simulating real condition. Some main factors which influenced the process of injection molding were found out after the simulation analysis of filling and flowing.

通过模拟真实注射条件，应用Moldflow软件对ABS扣板注射成型工艺参数进行了优化分析，得出影响注射成型顺利进行的主要因素，并模拟制定出扣板注射成型的最佳注塑压力、锁模力、模具温度、熔体温度、注塑时间、保压压力、保压时间和冷却时间。

Based on the balanced exergy grand composite curve and the improved shiftwork targeting method, the top-level analysis approach and its strategy are developed. It is employed to direct the analysis and diagnosis of the energy-utilization of the overall low-temperature process system in order to find out the optimal target to modify the process.

以低温过程系统平衡的有效能总组合曲线为分析工具，提出了基于改进轴功目标法的低温过程系统顶层分析方法，用以分析低温过程系统的能量流动，发现最佳的过程改进目标。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。