查询词典 optimal path

SSPP firstly computes a minimum hop primary path for each connection request, and it follows to compute two SRLG disjoint and minimum cost backup paths for each sub-path on the primary path.

共享子通路保护为每条业务请求计算一条最短的工作路由，并为工作路由上每段子通路各计算两条共享风险链路组分离且代价最小的保护路由。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

This staggered path configuration defines an elongated, tortuous path having a length greater than a height of the stack for eddy currents through the lamination stack, to increase impedance of an eddy current path therethrough.

此曲折路径的构形形成一条细长的曲折路径，对于通过该叠层片的叠放体的涡漩电流来说，其长度比叠放体的高度要长，从而提高了从中通过的涡漩电流的阻抗。

By taking the left path in the Path of Time, you will venture into the Warped Path of Time

在时间的路径中左边的路径，你将会进入扭曲的时间冒险一番

Based on the principle of chordal path multi-path ultrasonic flowmeter, the model of multi-path ultrasonic gas flowmeter that can adaptively adjust its weight coefficients was built using the methods of Gauss-Legendre integration and linear neural network.

在以弦向声道布置的多声道超声气体流量计原理的基础上，采用Gauss-Legendre数值积分和线性神经网络相结合的方法完成自适应调整权系数的多声道超声气体流量计建模。

For loading along curved strain path,it is found that the delay anglenot only depends on the curvature of the path but also on the rate of the curvature re-spected to the path are length.Therefore,we can conclude that Lensky's hypothesisof local determinability for delay angle is not hold for this material.

对沿曲线应变路径加载的情形，实验发现，滞迟角的变化规律不仅与路径曲率有关，而且与曲率的变化率密切相关，表明Lensky的&局部确定性&假设不再成立。

The liquor path includes the path for making the diluted liquor flowing from the absorber diffluent and flows respectively into the high-temperature generator and the exhaust heat recovery generator, and the path for making the diluted liquor that have been heated and condensed to medium concentration by the high-temperature exhaust gas in the high-temperature generator flows into the low-temperature generator from the high-temperature generator.

溶液路径包括使从吸收器中流出的稀释溶液分流并且分别流入高温发生器和废热回收发生器中的路径以及使在高温发生器中被高温废气加热并浓缩到中等浓度的稀释溶液从高温发生器流入低温发生器中的路径。

For considering the effect of stress path,the relations between the constitutive parameters in Gudehus-Bauer model and instantaneous stress path are analyzed and the stress-path factor is integrated into the hypoplastic constitutive model.

为了考虑应力路径的影响，分析了Gudehus-Bauer亚塑性模型参数与瞬时应力路径之间的关系，将应力路径影响引入亚塑性本构模型。

The non-inverting path is the direct path through the MUX and the inverting path is through the inverter.

非反向的路径是通过选择器的直接路径而反向路径是通过反向的。

The path of the Vedantic discipline is the path of negation,"neti", in which, by stern determination, all that is unreal is both negated and renounced. It is the path of jnana, knowledge, the direct method of realizing the Absolute.

吠檀多实践的是否认的道路，用严厉的决心来&否定&，所有不真实的都要否定和弃绝，是智慧、知识的道路，认识绝对者的直接方式。

Looking to bounce back from defeat against Cesena last weekend, the Calabrian boss will be sticking to his tried and tested 4-3-3, with Lopez and Sedivic joined up front in Giampaolo's absence by either Nanni or Plasmati.

鉴于上周末对切塞纳的比赛中反败为胜，这支南方球队将会更坚持其一贯而有效的4-3-3阵型，洛佩斯和塞德维奇将取代受伤缺席的詹保罗，和纳尼或者帕斯马蒂中的一个搭档锋线。

Meanwhile, their exposure to the more freewheeling ways of the West broadened dramatically.

另外，西方较自由的生活方式对年轻人的影响增大。