查询词典 opening

No recurring character from any previous season will die in the opening hour.

不会再有之前几季的主要角色开季死去。

Die lands should be 3-5 times the dimension of the die opening;entrance angles to the land should be as

模具面积应是模槽尺寸的3-5倍；入口角的度根据特殊情况考虑，尽可能小而实用，但是， 10 °-60 °是常见的。

The occurrence of wrinkling is attributed to the large die gap, which is the difference between the side length of the die cavity opening and the side length of the punch head.

出现的皱折是由于模具间隙大引起的；该间隙在模具腔口的侧面距离和冲头侧面距离之间有差别。

The operating noise is lowered greatly, and the opening and locking die vibration reduced; the service life of equipment and die is prolonged, and working environment improved

注塑机运行噪音明显降低，开、锁模振动减轻，延长设备和模具的使用寿命，改善工作环境。

It embeds knowledge that formerly resided only in the minds of senior die designers, opening the door for more opportunity with greater access to this knowledge.

可定制的冲模库、标准件库和插入组厍加快冲模结构设计并确使我们的客户的完整过程有效地被处理。

A heated adapter tube carries the melted plastic from the extruded head to the opening in the center-fed die.

一个加热调适管把来自挤压头的热容胶引入到中心馈电的模具开口处。

It is suggested that the wrinkling is due to the large unsupported area at the draw wall during the stamping process, also, the side length of the punch head and the die cavity opening are different owing to the die gap.

它暗示起皱是由于拉伸过程中存在大的无支持区域，而且，冲子头部的边长和模腔的打开也由于模具间隙而不同。

Using the finite element method and based on finite element simulation of profile extrusion process, the effect of local extrusion ratio, die land area and the distance between extrusion cylinder center and die opening center on mental flow velocity is studied. The deformation flow laws on profile extrusion process are obtained.

本文采用有限元方法，以型材挤压过程的有限元模拟为基础，研究了局部挤压比、挤压带面积和模孔距离对金属流动速度的影响，获得了型材挤压过程的变形流动规律。

Lu was going to explore the truth bent suddenly see a large locust nearby, two large opening and die together, eating quickly Leaves of Grass.

鲁班正想俯身探究其中的道理，忽然看到近处有一只大蝗虫，两枚大板牙一开一合，很快吃着草叶。

In order to examine the effect of die gap on the wrinkling, the stamping of a tapered square cup with three different die gaps of 20 mm, 30 mm, and 50 mm was simulated. In each simulation, the die cavity opening is fixed at 200 mm, and the cup is drawn to the same height of 100 mm.

为了验证模具间隙对起皱的影响，模拟了一个在从20MM， 30MM和50MM不同模具间隙下的锥形方杯的冲压，在每次仿真中，模腔打开固定在200MM，杯形拉伸同样高度100MM。

As of Tuesday, Google's results were still censored in China.

截至周二，谷歌的搜索结果仍受中国审查。

In order to make the positive action increase and negative one decrease, the sub-forces of the social factors must be adjusted to form a centripetal force.

在这一过程中，人的主体性发挥是社会有机体健康发展的灵魂。