查询词典 on the increase

3D reconstruction is one of the most challenging problems in computer vision. This project uses CAD model to increase the accuracy,robustness and speed of 3D reconstruction and five different works are conducted: 1 research on space curve 3D reconstruction method based on high curvature point nad turning point; 2 free-form curve 3D reconstruction based on B-spline and BURBS; 3 Active surface affine reconstruction based on single frame; 4 Matching and reconstruction of 3D sparse points; Data fitting method based on the iteration of nearest point.

三维重建是计算机视觉中公认的难题，本项目使用CAD模型来提高三维重建的精度、稳健性和速度的思路，围绕着空间曲线和曲面的三维重建和匹配开展了以下五个方面的研究：1）基于高曲率点和拐点分割的空间曲线三维重建方法研究；2）基于B样条和NURBS表示的空间自由曲线三维重建方法研究；3）基于单帧图像的有源曲面仿射重建；4）三维离散数据的匹配与重建；5）基于迭代最近点的数据拟合方法。

Based on electro-characteristic and double electric layers models, directional mechanisms of soy protein molecular are analyzed for the first time on DC heating condition. After the main factors which effect soy protein gels transparency and strength being studied on DC heating condition, the different affects on soy protein gels transparency and strength by DC heating and water bath heating are analyzed and compared, and the transparent mechanisms of soy protein gels are further explored. In addition to temperature action as water bath heating, DC heating is added as electric field directional action. As a results, heating rate is increased. Directional range degrees of soy protein molecules are raised. These advantage the increase of soy protein gels transparency and strength. Microstructures of soy protein gels forming on DC heating condition are observed by SEM and the results showed that ordered structure of transparent soy protein gels on DC heating condition is more ordered than that of transparent soy protein gels on water bath heating condition.

首次从大豆蛋白的电特性和双电层模型上分析了直流电加热条件下，大豆蛋白分子定向的机理；通过对直流电加热条件下影响大豆蛋白凝胶透明性和强度主要因素的研究，分析和比较了直流电加热与水浴加热对大豆蛋白凝胶透明性和凝胶强度的不同影响，又进一步探讨了大豆蛋白凝胶透明的机理；直流电加热除了水浴加热中的温度作用以外，又增加了直流电场的定向作用，提高了加热速率，提高了大豆蛋白分子定向排列的程度，有利于蛋白质凝胶透明性和强度的提高；利用SEM对电场下大豆蛋白凝胶微观结构的观察，进一步证明了直流电加热比水浴加热形成的透明大豆蛋白凝胶微观结构具有更高的有序性。

With the increase of the carbon dioxide density to enhance the impact on the wheat conductivity and the MAD density, the rise in the CO2 density causes the reduction of the exosmosis conductivity and the increase of the MDA content, the change of which is the same as the exosmosis conductivity.

第三部分是CO2浓度升高对小麦叶片活性氧的影响，再次增加二氧化碳浓度进行实验，观察小麦H2O2含量和超氧负离子自由基的影响，得到的结果是高浓度二氧化碳可以降低小麦叶片中活性氧的含量，因而能够减轻H2O2的毒害作用。

Each medicine used in the study totally has obivious effect on lens sodium-pump. Either on the molecular and cellular level or on the histological and organic level , they all have their distinctive demonstration. 1.Ouabain、Digoxine、DMSO decrease the expression of αsubunit of sodium pump on mRNA level , the cell morphology and ultramicroscopic structure demonstrated destructive effect,it indicates the cause of cataract of the medicines.2.D-thyroxine、Amphotericin B、Vitamin E increase the expression of αsubunit of sodium pump on mRNA level ,from the demonstration of the cell morphology and ultramicroscopic structure ,it indicates the medicines have protective or anti-distructive effect on lens.3.The medicines have isoform-specific action on lens sodium-pump,it indicates exploitting isoform-specific medicine has a promising clinical application.4. Lens sodium-pumps are inhibited probably lead to cataract, so in clinical medication, especially to the cardiovascular doctor, while he is using the sodium-pump inhibitors, he should pay more attention to adjust the dosage and duration of the drug therapy. 5. To creat the animal model of cataract through inhibiting lens sodium-pump, whether it can be a kind of classical method or not, it is worthy of further research.

本研究所选用的药物对晶状体钠泵均有明显的影响作用，在分子水平、细胞水平、组织器官水平均有特异的表现：1、哇巴因、地高辛、二甲基亚砜三种药物可降低晶状体钠泵α亚单位在 mRNA水平的表达，在细胞形态和超微结构上表现为损伤效应，提示了其潜在的导致白内障的可能。2、D甲状腺素、两性霉素B、维生素 E三种药物可升高晶状体钠泵α亚单位在 mRNA水平的表达，从细胞形态和超微结构上的表现，提示了其对晶状体有保护作用或抗损伤效应。3、药物作用于晶状体钠泵具有重整异构特异性，提示了开发出特异的具有重整异构作用的药物是极有临床应用前景的。4晶状体钠泵抑制后可能导致白内障的发生，故临床用药，尤其是心内科医生在使用这些钠泵抑制剂时应注意调整用药剂量及药物疗程。5 通过抑制晶状体钠泵来制作白内障动物模型能否成为一种经典的制作方法，还有待于进一步研究。

The results show that the optimal value of CoCl2 concentration is 0.2 mol/L and the maximum adsorbed amount is 19.674 mg/g onto this adsorbent. The adsorption capacity of phosphine onto CoCl2-modified ACF decreases with the increase of temperatures. The maximum absorbed amounts are 19.674 mg/g at 298 K, 13.537 mg/g at 313 K and 11.087 mg/g at 328 K, respectively. It is found that the Freundlich equation is more suitable for the description of phosphine adsorption process than the Langmuir equation. The isosteric heat of adsorption decreases with the increase of the surface loading on CoCl2-modified ACF, which means that CoCl2-modified ACF adsorbent has an energetically heterogeneous surface. Meanwhile, adsorptive phosphine removal performance may be a dominant of physical adsorption when the heat of adsorption is 16-24 kJ/mol, the CoCl2-modified ACF adsorbent will be one of the candidates for tail gas purification of airtight calcium-carbide furnace and recycle of phosphine.

研究结果表明：浸渍液浓度最佳值为0.2 mol/L，此改性ACF对PH3的饱和吸附量为19.674 mg/g；PH3在CoCl2改性ACF上的吸附量随温度升高而迅速降低，在298，313和328 K时PH3的饱和吸附量分别为19.674，13.537和11.087 mg/g；Freundlich吸附等温方程较好地模拟了PH3在改性ACF上的等温吸附；PH3气体在改性ACF上的等量吸附热随吸附量的增大而减小，表明改性ACF吸附剂表面能量的不均匀性；吸附热在16~24 kJ/mol范围内，过程为物理吸附，有利于密闭电石炉尾气的净化。

No matter the quality of coal, the size composition and water content as well, due to the bad environment of coal production and the vibration in the process of transportation, there always has some coal and other materials left which was very easy to cake on the bottom of the mine car after unloading. If we do not clean these remaining coal and rock meal soonly, they would be heavier and solider, which would increase the weight of mine car so that decrease the effective volume of it. Then it would not only affect the transportation ability of mine car directly and make the intense condition of the transportation system, but also increase the waste of electric power, and even make substantial difficulty in starting the spacial vehicle while transporting the electrical machinery truck. So cleaning the bottom of the mine car become espectially important.

不论煤质，粒度组成及含水量如何，由于煤矿生产环境的恶劣，加之在运输的过程中的振动等原因，卸车之后总会有少量的煤炭，煤矸等易粘结的物料粘结在矿车车箱底部及邻帮若不将这些残留煤，岩粉及时清除干净，则会越积越厚，越积越结识，增加了矿车自重，使矿车的有效容积减少，它不仅直接影响着矿车的运输能力，造成了运输系统的紧张状况，而且增加了电力资源的浪费，甚至使电机车运输是空列起动发生困难，所以清理车底的问题，在煤矿就显得尤为重要。

Firstly, by using DSC, we analyzed the effect of the type and content of initiators on the curing reaction, Then, through FTIR, we discussed the final degree of cure of the cured resin and the performance of the cured resin by testing the static mechanical performance and DMTA, found that moderate content and ratio of the initiators system can cause the moderate cure temperature, increase of exotherm and the final degree of cure result from the cooperation effect of the two kinds of initiators, and found that the cooperated initiators system can effectively increase the final degree of cure even in low content.

通过差示扫描量热法分析了不同固化剂体系对树脂固化行为的影响，用红外光谱分析了不同固化剂体系下的浇铸体的固化度，并对树脂浇注体静态力学性能及动态机械热分析，认为不同活性的固化剂联用存在协同效应，使固化反应温度适中，固化反应更加充分，提高树脂固化度和扩大聚合物网络，使树脂浇注体拥有良好的力学性能和耐热性。

The effects of strain rate on plastic formation and dynamic recrystallization of 7050 aluminum alloy were discussed. The results show that the deformation of the specimen is inhomogeneous, and the effective strain in the center of the specimen is maximum. The deformation inhomogeneity increases with the increase of strain rate. The effective stress of specimen is inhomogeneous. As the strain rate increases, the minimum stress value moves from the drum-shaped region to the heart of specimen. The standard deviation of dynamic recrystallization grain size decreases with the increase of strain rate.

模拟结果表明，热变形过程中，试样的各个部位的变形分布不均匀，心部的等效应变最大，变形的不均匀性随应变速率的增大而增大，但是变化的程度不大；试样内部各部位的应力大小分布不均匀，随应变速率的增大，最小应力值由自由变形的鼓形区域逐步向心部移动；动态再结晶晶粒尺寸标准偏差随应变速率的增加而减小。

The desulfurization experiments of CaO samples with various fractal dimensionswere carried out in the TGA to investigate the influences of fractality on the sulfationreaction, and the evolution of pore structures during the reaction. Under certainsulfation conditions, the calcium conversions of the CaO samples increase with theincrease in fractal dimension when fractal dimension is less than 2.68, and decreaseswhen it is more than 2.68. In the range of the experiment temperatures, the calciumconversion for a sample with a lower fractal dimension increases with the increase inthe temperature, and for a sample with a higher fractal dimension there exist anoptimum temperature at which the sample can reach the highest calcium conversion.

选用具有不同分形结构的CaO试样进行了硫化实验，研究孔结构的分形特性对硫化反应的影响以及硫化过程中分形孔结构的变化特性，实验结果表明，在一定的分形维数范围内，随着分形维数的增加，钙利用率增大，但分形维数超过一定值时(约为2.680)，钙利用率反而降低。

Experiment results indicate that the magnetic fluid flux has a direct relation with the magnetic field under the effect of traveling wave magnetic field. The bigger the magnetic field is, the more the flux is, when the structure of the magnetic fluid travellig pump and the saturation magnetization of magnetic fluid are constant. The volumes of the magnetic fluid from the travelling wave pump increase from 1.9 ml to 3.1 ml, when the magnetic field intensity increases from 25 900 A/m to 40 000 A/m. In addition, the change rate of the magnetic fluid decreases with the increase of the magnetic field due to the effect of magnetic field on magnetic fluid viscosity. The bigger the saturation magnetization of the magnetic fluid is, the more the flux is.

结果表明，行波磁场作用下的磁性流体流量与磁场的强度有直接关系：在磁性流体行波泵结构和磁性流体饱和磁化强度相同的条件下，磁场强度越强，其流量越大；当磁场强度从25900A/m增加到40000A/m时，单位时间内从行波泵内流出的磁性流体的体积由1.9 ml增加到3.1 ml；随着磁场强度的不断增加，磁性流体流量的变化率由于磁场对其粘度的影响而减小；而磁性流体的饱和磁化强度越大，其流量也越大。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。