查询词典 on condition that

The formula was established about calculating design parameters and technological parameters of ideal strip and bent strip in the period of forming. The thesis presented how to calculate the deformed area length and contact are radius of contact deforming between two elastic bodies on condition of the friction. The calculating formula of pinch force about plate-strip pinch mill was given and the results were analyzed that friction coefficient and radius of pinch rolls are very important for determining pinch force. Moreover, the rule of deforming and stress distribution of different 〓 ratio were gained on condition that the deforming was considered to be non-uniform distribution in the gap. The differential equations were got that calculate the displacements of large deflection of elastic cantilever rectangle plate with fixed end and the formula of the Finite Strip Method was conducted to study the regularity of mid-plane displacements, deformation and stresses for elastic-plastic large deflection bend of cantilever parallelogram plate with fixed or slidable end by integrating Prandtl-Reuss equation.

建立了一套完整的设计参数计算公式和在成型过程中理想带钢或具有月牙弯带钢的工艺参数的调整公式；在考虑摩擦力的条件下，对两弹性体接触变形过程中的接触变形区长度和接触弧半径用位移解法进行了研究，推导了板带递送机的递送力计算公式，从而得知在递送机设计过程中，应选择适当摩擦系数和辊身直径；另外，还从辊缝内带钢实际变形出发，分析了对于不同的〓值，带钢的变形规律及应力分布状况；建立了固定端悬臂矩形板弹性大挠度弯曲变形的控制方程，并且在对Prandtl-Reuss方程的积分处理的基础上，导出了固定端和滑动端悬臂平行四边形薄板的弹塑性大挠度的中面伸展位移、变形和应力的有限条元法公式，编写了Fortran语言计算程序，在各种参数条件下，对螺旋焊管成型过程变形规律进行了全面的分析研究，从而为螺旋焊管的生产和进一步的改进提供了理论依据。

Under the condition of vanishing perturbation, a sufficient condition of the stability of the system is derived.

然后在零扰动情况下，给出了扰动非线性切换系统稳定的充分条件。

The proposed control method compensates the phase error on vector control condition quickly, and always keeps the vector control condition.

建议中的管制方法补偿相位误差矢量控制状态很快，始终保持矢量控制的情况。

The result showed that the optimal condition of inorgano-absorbent manufacture as following: concentration of vitriol is 15%, the bentonite carrier must be soaked in the 0.4% La(superscript 3+) solution, the pH is 10, microwave radiation power is 340 W for 5 min. The optimal condition of organo-absorbent manufacture process as following: concentration of CTMA is 5%. The rate of wave must 166 W and the time of radiation is 6 mi In addition, the experimental results showed that with inorgano-absorbent the pH number is 3~6 and the reaction time is 45 min, the removal efficiency of phosphor will be up to 99% and the amount of adsorption will be up to 41 mg/g. And with organo-absorbent the pH number is 3~4 and the reaction time is 45 min, the removal efficiency of phosphor is more 30% than that of inorgano-absorbent. The removal efficiency of phosphor will be up to 99% and the number of adsorption will be up to 60 mg/g.

实验表明：①制备无机稀土吸附剂的适宜条件为：硫酸浓度15%，镧浓度0.4%，浸渍pH值10，微波功率340 W，辐射时间为5 min；②制备有机稀土吸附剂的适宜条件为：表面活性剂浸泡浓度为5%，微波功率为166 W，微波辐射时间为6 min；③无机稀土吸附剂当溶液的pH值为3~6，振荡时间为45 min时，对磷去除率为99%以上，吸附量达到了41 mg/g以上，有机稀土吸附剂当溶液的pH为3~4，振荡时间为45 min时，其效果比原来镧改性的无机吸附剂吸附量提高了30%，磷去除率为99%以上，吸附量达到了60 mg/g以上。

Based on the conclusion of experimental law, the photoelectric threshold condition is obtained for the semi-insulating GaAs photoconductive switch under the non-linear mode, pointing it out that, when the optic-energy triggers off the switch to meet the prerequisite that n_0L is greater than or equal to 10~(12)cm~(-2), the necessary condition is achieved for high field domain and meanwhile the threshold electric field serves to produce charge transmission effect within the material.

在总结实验规律的基础上，得到半绝缘GaAs光电导开关非线性模式的光电阈值条件，指出当光能触发使开关满足n0L≥10~(12)cm~(-2)时，达到形成高场畴的必要条件，阈值电场的作用是使材料体内产生电子转移效应。

The result of abrasion test and welding tests show, the crafts of adopting parted type structure to make tamping pick is viable theoretically, the pickax boot wearable material we have selected havent appear brittleness desquamation under the condition of test, and the ratio of performance and price of the material is higher; The welding joint has no obvious welding bug under the condition of test, the break mode of welding slot metal is mainly toughness break, and the craft performance of the weld material we have selected is all right, the welding craft we have established is suitable to the occasion and feasible.

磨损试验和焊接试验结果表明，采用分式体结构制造捣镐这一工艺理论上是可行的，所选镐靴耐磨材料在试验条件下未见脆性剥落，而且性价比较高；焊接接头在试验条件下没有明显的焊接缺陷，焊缝金属断裂方式主要是韧性断裂，而且所选焊接材料工艺性能良好，所制定焊接工艺切实可行。

In order to imitate the unbounded space wave propagation,the non local boundary condition is used as the absorption boundary condition to cut off the computation domain,and the problems of plane wave incidence at different angles are calculated with the high order PE algorithm.

文章通过引入Padé逼近构造高阶抛物线方程算法，用非局部边界条件作为吸收边界条件，截断计算区域以模拟无界空间波的传播，结合高阶PE算法分别计算不同角度平面波的入射问题。

Firstly, the soil samples are gathered from the same section such as surface layer soil samples gathered from 0cm to 15cm depth and representation on studied object. Secondly, the precondition of tested samples must be the same. This study indicates that the tested samples must be 1mm diameter, over-dried at 40℃ for 24h and airtight cooling for 24h before measured for air-dry samples, and softly planish the surface at measuring. Lastly, the illuminating condition of light must be the same. This study indicates that the testing geometric condition are light source angle 15°, light source distance 30cm and sensor distance 15cm for soil hyperspectra indoor. The surface of white reference must be the same plane of that of sample.

第一个环节的"相同"是指田间土壤样品采集时的剖面位置一致，如表层土都采集0～15cm深度范围内的土壤，且所采集的样品应能尽量具备研究对象的代表性；第二个环节的"相同"是指土壤制备过程中的一些前处理条件应一致，建议土壤光谱测试样品的粒径1mm，风干土壤样品测试前在40℃恒温条件下烘24小时，然后密闭冷却24小时，测试时土壤表面进行稍稍压平处理；第三个环节的"相同"是保证测试光照条件的一致性，建议在50W卤素灯、8°探头角条件下，采用15°的光源照角度、30cm的光源距离和15cm作为室内士壤高光谱测试几何条件，测试时除遵循光谱测试指南的要求外，还须保证参考板表面与测试土壤样品的表面在同一平面上。

To obtain quadratical convergence, however, strict complementarity condition at the Danskin point was used. The condition is too strict to be satisfied in many practical problems such as discrete semi-infinite minimax problem. Another kind of Newton method for finite minimax problems was presented by E. Polak and, without strict complementarity at the Danskin point, superlinear convergence (of order 3/2) was proven.

Polak等人提出了一种直接求解极大极小问题的二阶收敛的牛顿法，但是为获得二阶收敛速度要求在Danskin点处满足严格互补条件，这个条件太强，很多实际问题尤其是半无限极大极小问题的离散化不满足该条件；他们又给出另外一种牛顿法，在不假设严格互补条件成立的情况下，证明了它的超线性（3/2阶）收敛性。

Morphological and anatomical observationsshowed that the pol CMS plants in DGCMS-Yi-3A were complete sterile and hadno pollen sac differention at higher temperature condition,and were partialsterile and had 1-3 pollen sacs in each anther at lower temperature condition.

花器形态和花药发育的解剖观察表明，DGCMS-宜3A中表现波里马细胞质雄性不育的植株在高温条件下表现为彻底雄性不育，无花粉囊的分化；在低温条件下，表现部分雄性不育，可分化出1-3个花粉囊，产生少量可育花粉。

Putt your way through 36 fun-filled holes of minigolf on 3D designed courses with elevated greens, bunkers, bridges and water hazards, among other crazy obstacles.

您的推杆方式，通过36个有趣的填孔迷你的三维设计的课程，以提升绿党，掩体，桥梁和水的危害，除其他疯狂的障碍。

Some participles can be used either as attributes or as predicatives.

有些分词既可当定语用，也可当表语用。